This is a list of PC error codes

This is a list of PC error codes.

00010300 on a 90 or 95 me= ans Processor Board. If a 20-MHz board is installed, and the processor is = not a 487SX, verify that the jumper is in positions 2 and 3. (487SX is indicated on the processor.)
000104XX on a 90 or 95 me= ans System Board
000107XX or 000110XX on a= 90 or 95 means System Board Memory or System Board
000112XX or 000113XX on a= 90 or 95 means check adapters then System Board
000114XX on a 90 or 95 me= ans SCSI Adapter
00011600 (Fatal) - on a 9= 0 or 95 means planar board port read/write failure
00011800 on a 90 or 95 me= ans Memory/planar board parity or L2 cache NMI error logged, critical error log entry exists
00011900 (Fatal) - on a 9= 0 or 95 means Downlevel 82077 diskette controller
00012000 (Fatal) - on a 9= 0 or 95 means Processor self test error
00016100 on a 90 or 95 me= ans Dead battery
000163XX, 000164XX, 00016= 5XX or 000169XX means Set Configuration/Features. Run SETUP. If not successful, check System Board
000166XX on a 90 or 95 me= ans an adapter is failing
00017000 on a 90 or 95 me= ans ASCII setup conflict
00017100 (Fatal) - on a 9= 0 or 95 means Rolling bit test failure on CMOS shutdown address byte
00017200 (Fatal) - on a 9= 0 or 95 means Rolling bit test failure on NVRAM diagnostic byte
00017300 on a 90 or 95 me= ans Bad CMOS/NVRAM checksum. Verify the Enable and Disable Settings
00017400 on a 90 or 95 me= ans Bad configuration, changed device. If Automatic configuration does not solve the problem, run Advanced Diagnostics.
00017900 on a 90 or 95 me= ans NVRAM Error Log contains maximum log entries, clear system error log <= /li>
000194XX Check System Boa= rd then check System Board Memory
0002xxxx on a 90 or 95 me= ans System Memory error
00020XXX on a 90 or 95 me= ans System Board Memory
000210XX or 000211X on a = 90 or 95 means Processor Board or System Board Memory
000215XX, 000216XX, 00022= 5XX, 000226XX, 000240XX or 000255XX on a 90 or 95 means System Board Memory= or System Board
000252XX on a 90 or 95 indicates system board problem. Even it Intermittent error, Run advanc= ed memory diagnostics in loop mode.
00029100 on a 90 or 95 ma= y be corrected by running Automatic Configuration. There is a Checksum value mismatch
00029200 on a 90 or 95 ma= y be corrected by running Automatic Configuration. There is a Checksum value mismatch
00029300 on a 90 or 95 ma= y be corrected by running Automatic Configuration. There is a Checksum value mismatch
00029400 on a 90 or 95 ma= y be corrected by running Automatic Configuration. There is a Checksum value mismatch
000295XX or 000296XX on a= 90 or 95 means System Board Memory or System Board
000298XX on a 90 or 95 me= ans System Board or System Board Memory
000301XX or 000302XX on a= 90 or 95 means Keyboard, Keyboard Cable or the System Board
000303XX on a 90 or 95 me= ans System Board, Keyboard or Keyboard Cable
000304XX on a 90 or 95 me= ans System Board or Keyboard
000305XX on a 90 or 95 me= ans Keyboard Cable (Keyboard voltage error)
00030600 on a 90 or 95 me= ans Unsupported keyboard attached
000401xx on a 90 or 95 me= ans parallel port error -- replace planar
0006xxxx on a 90 or 95 me= ans Diskette (media), diskette drive or Power Supply
000602XX on a 90 or 95 me= ans Defective diskette
0007XXXX on a 90 or 95 me= ans defective Math Coprocessor or Processor Board
0011xxxx on a 90 or 95 me= ans primary async port error -- replace planar
001102XX or 001106XX on a= 90 or 95 means System Board or any serial device
001107XX on a 90 or 95 me= ans Communications Cable or System Board
001108XX or 001109XX on 9= 0 or 95 means system board or any serial device
001202XX or 001206XX on a= 90 or 95 means Dual Async Adapter/A or any serial device
001207XX on a 90 or 95 me= ans Communications Cable or Dual Async Adapter/A
001208XX or 001209XX on a= 90 or 95 means Dual Async Adapter/A or any serial device
0014xxxx on a 90 or 95 me= ans printer error or system board
004611XX or 004630XX on a= 90 or 95 means Multiport/2 Interface Board or Multiport/2 Adapter
004612XX, 004613XX, 00464= 0XX or 004641XX on a 90 or 95 means Memory Module Package or Multiport/2 Adapter
004650XX on a 90 or 95 me= ans Multiport interface cable
007509XX on a 90 or 95 me= ans Display or XGA Display Adapter/A
007510XX on a 90 or 95 me= ans XGA Display Adapter/A, Video Memory Module or System Board
00860xxx on a 90 or 95 me= ans mouse error (see 860x error codes)
008601XX or 008602XX on a= 90 or 95 means System Board or Pointing device
008603XX on a 90 or 95 me= ans System Board
008604XX on a 90 or 95 me= ans System Board or Pointing device
0096xxxx on a 90 or 95 me= ans SCSI error (see SCSI error codes at end)
010002XX or 010006XX mean= s 90 or 95 Multiprotocol Adapter/A or any serial device
010007XX on a 90 0r 95 me= ans Communications cable or Multiprotocol Adapter/A
010008XX or 010009XX on a= 90 or 95 means Multiprotocol Adapter/A or any serial device
010102XX, 010106XX, 01010= 8XX or 010109XX on a 90 or 95 means Modem Adapter/A or any serial device <= /li>
0107XXXX on a 90 or 95 me= ans 5.25 Inch Diskette Drive or 5.25 Inch Diskette Adapter/A
0112xxxx on a 90 or 95 me= ans SCSI error (see SCSI error codes at end)
0129XXXX on a 90 or 95 co= uld mean Processor Board Cache (256KB), Processor Board or System Board
01291700 on a 90 or 95 me= ans processor board. If a 20-MHz board is installed, and the processor is a 487SX, verify that the jumper is in positions 1 and 2. (487SX is indic= ated on the processor.)
01293000 (Fatal) - on a 9= 0 or 95 means Processor board EEPROM selection jumper is currently selecting Stage2 POST to begin POST execution, switch the jumper
01299000 on a 90 or 95 me= ans Vital Product Data processor board error
01308200 on a 90 or 95 me= ans characters on info panel are in error
0137xxxx on a 90 or 95 me= ans secondary async port error -- replace planar
0141XXXX on a 90 or 95 me= ans Realtime Interface, Coprocessor or Portmaster Adapter/A
0147XXXX, 0152XXXX on a 9= 0 or 95 means XGA Display Adapter/A, Video Memory Module or System Board
0164XXXX on a 90 or 95 me= ans 120MB Internal Tape Drive Diskette Cable System Board
016500XX on a 90 or 95 me= ans 6157 Tape-Attachment Drive or Adapter
016520XX on a 90 or 95 me= ans 6157 Streaming-Tape Drive
016540XX on a 90 or 95 me= ans 6157 Streaming-Tape Drive or 6157 Tape-Attachm= ent Adapter
0166XXXX or 0167XXXX on a= 90 or 95 means Token-Ring Network Adapter/A or system board
0200XXXX on a 90 or 95 me= ans Image Adapter/A, Video-Memory Module or System Board
0208XXXX on a 90 or 95 me= ans Any SCSI Device. Verify there are no duplicate SCSI ID settings. See S= CSI errors below.
0210xxxx on a 90 or 95 me= ans SCSI hard file error (see SCSI errors at end)
0211XXXX on a 90 or 95 me= ans SCSI Tape Drive, SCSI Adapter or SCSI Cable
0215XXXX on a 90 or 95 me= ans SCSI CD-ROM Drive, SCSI Adapter or SCSI Cable =
0217XXXX on a 90 or 95 me= ans SCSI Rewritable Optical Drive, SCSI Adapter or SCSI Cable
I99900XX on the 90 or 95 information panel. Verify an operating system has been loaded onto the default hard disk drive.
I999001X Invalid hard disk Initial Microcode Load record. A valid master IML record was not found= on the hard disk.
I9990015 on a 90 or 95 followed by 96-8N1 means that the system could find no output display. Check that cable is connected.
I999002X Hard Disk Initial Microcode Load Record Load Error
I999003X Incompatible Disk Initial Microcode Load Record/Planar. The Initial Microcode Load boot record loaded from the hard disk did not have a planar ID matching the system.
I999004X Disk IML record incompatible with processor board
I999005X Disk IML not attempted
I999006X Disk stage 2 ima= ge load read error
I999007X Disk stage 2 checksum (read) error
I999009X System Board BIOS newer than Disk IML Partition
I99900X1 Invalid Diskette Initial Microcode Load Record. A valid master Initial Microcode Load record was not found on the diskette.
I99900X2 Diskette Initial Microcode Load Record Load Error
I99900X3 Incompatible Dis= kette Initial Microcode Load Record/Planar. The Initial Microcode Load boot record loaded from diskette did not have a planar ID matching the syst= em.
I99900X4 Incompatible Diskette Initial Microcode Load Record/Processor Card. The Initial Microcode Load boot record loaded from diskette did not have model/submodel byte value matching the system.
I99900X5 Diskette Initial Microcode Load Not Attempted. Diskette IML was not attempted because o= f a fatal disk IML error or active system security.
I99900X6 Diskette POST/BIOS/BASIC Image Load Error. The system image could not be loaded from the diskette.
I99900X7 Diskette stage 2= IML checksum error
I99900X9 System Board BIOS newer than Diskette BIOS
I9990301 No bootable devi= ce, hard disk, or diskette
I9990302 Invalid disk boot record (Missing operating system)
I9990303 System partition boot failure
I9990304 No bootable devi= ce with ASCII Console
I9990305 No Startable dev= ice found, verify startup sequence
I9990306 Invalid CDROM or= R/W optical drive error
I9990401 Unauthorized acc= ess, clear Power On Password
I9990402 Missing IBM copyright notice, alternate processor error
I9990403 Incompatible Disk Initial Microcode Load Record. The IBM ROM IML routine would have dete= cted incompatible incompatible IML record. The ROM may not be an IBM ROM so= the system access error is generated.
I99906xx IBM overlay erro= rs
I99980xx ThinkPad system partition error
101 Main system board failure/Processor error. PS/2 - Interrupt failure. PCC - Interrupt controller failure
102 BIOS ROM checksum err= or. (Try reseating the ROM chips!). PS/2 - Timer failure or Real time cloc= k 64 byte CMOS RAM test. PCC - System timer 2 failure
103 BASIC ROM(s) checksum error. PS/2 - Timer interrupt failure or 2Kb CMOS RAM test. PCC - Syst= em timer 0 failure
104 8259 interrupt contro= ller error. PS/2 - Protect mode failure or Real time clock timing test
105 8253 timer error. PS/= 2 - last 8042 command not accepted. PCC - DMA controller failure.
106 (PS/2) Converting log= ic test failure
107 Interrupt failure on = 339 AT. Remove cards one at a time until you find the failing adapter. If problem persists after all cards except Fixed Disk adapter, or the pri= mary display adapter, then the system board is failing. PS/2 - Hot NMI test=
108 (PS/2) Timer bus test. (PCAT) Memory error, or memory too slow for CPU
109 Direct memory access = test error. PS/2 - Low meg chip select test or DMA or arbitration error.
110 (PS/2) Planar parity =
111 (PS/2) I/O parity or 80286 type protect mode test. -- POSSIBLE IMAGE ADAPTER error if (See 20000 series messages)
111/???? is a Channel I/O Ready line problem with the 5250 emulation card. A new ADF file for the card is necessary. It should be version 1.01, not 1.00. What 111 really means is that an NMI was signalled and the source was the IOCK line (on PC) or the CHCK line (on MicroChannel). On PCs, this was pulled by par= ity error detected on memory expansion cards. On MicroChannel PS/2s, there= may be other cards which pull this error line active for other reasons. If= you have a memory expansion card, this is very likely to be the source. The system BIOS cannot determine what card caused the problem. Possible fi= x -- replace 3 chip SIMMS with 9 chip SIMMS (especially for OS/2).
112 (PS/2) Watchdog time = out or Test 80386 new extended registers
113 (PS/2) DMA arbitration time out or Test 80386 new instructions. The hard disk drive may have = to be replaced. There is a Retain reference for the PS/2 model 55: H06437= 7. NOTE: "0002 1130" is basically a "211" error code, which is a memory error on the planar. The "3" indicates SIMM socket A2 (1=3DA1,2=3DB1,3=3DA2 etc) and the last character ("0&q= uot;) gives the SIMM speed. Alternately this could be a DOS error -- see abo= ve on internal stack overflow. Also, it is possible that a PS/2 113 error= can arise from certain programming routines used with a Soundblaster MCV. = See appends in ERRCODES FORUM starting on 93/01/03.
114 (PS/2) External ROM checksum error or Test 80386 32-bit addressing mode
115 (PS/2) Test 80386 pro= tect mode (80386 TSSs, VM8086, Paging)
116 (PS/2) Test 80386 16/= 32 bit (mult., div., sub., add)
118 (PS/2) Logged memory error - run Adv Diags (90 and 95)
119 (PS/2) 2.88MB diskette drive is installed but not supported
120 (PS/2) Processor self test failed
121 Unexpected hardware i= nterrupts occurred. (PS/2) Test Hot reset of processor (via port 90H)
129 (PS/2) Processor has = been changed. Run Configuration.
0129 1200 means that a watchdog timeout occurred. This usually indicates (1) a runaway application or (2) an errant system board.
0129 1300 Indicates that a MicroChannel bus timeout has occurred -- see 12913
131 Cassette wrap test failed. PS/2 - Test DMA compatibility registers
132 (PS/2) Test DMA exten= ded registers
133 (PS/2) Test DMA verify logic
134 (PS/2) Test DMA arbitration logic
141 PS/2 - System-status display assembly. 80% chance it's the system board
151 SYSTEM BOARD Real Time Clock Failure (or CMOS ERROR on 5170 -- PC/AT)
152 (PS/2) Real time cloc= k or CMOS error -- run diagnostics from a cold boot WITHOUT a password installed -- you can get a 152 error when trying to test the LOCKED ar= ea of the CMOS Real-Time Clock chip that CONTAINS the password. (Try it w= ith the password removed, and from a cold-boot. If you still get a 152, you might have to replace either the battery or the planar).
153 (PS/2) Bat= tery failure
160 (PS/2) Planar ID not recognized (Check that the I/O channel riser card is firmly plugged in= )
161 AT systems options not set (run SETUP) PS/2 - Battery dead or not connected
162 AT systems options not set (run SETUP) << See 164 PS/2 - Systems options not set (Run Configuration)
163 AT time & date not set (run SETUP). PCC - Real-time clock not updating
164 AT memory size error = -- To correct it, run SETUP on Diagnostics Disk. PS/2 - Memory Size error (run Setup on Reference Disk). Make sure that external units (like disk drives) are powered on before powering up the system unit -- you may w= ant to leave your external drive on. "System options are not set" means that "the configuration stored in the CMOS doesn't match reality" but also that the code thinks that the rest of the syste= m is usable - and will run diagnostics for whatever it can find - memory ch= eck, drive check, etc. Computers are unreasonable, so minor details can cau= se major trouble. You'll need the installation ("options") diskettes for any extra hardware that's been added (modems, etc.).
165 PS/2 - systems options not set - card ID mismatch (run SETUP)
166 PS/2 - card busy erro= r
167 PS/2 - clock not updating. If you are continually losing SETUP data, it means either the battery is low or not connected in some way OR the system board CMOS memory is defective which requires getting the system board replaced. = It nearly always is the battery or the battery connections.
168 - PS/2 model 55 -- a medialess box with a faulty RIPL ROM.
169 (PS/2) Planar/process= or card mismatch (Run SETUP)
170 (PCC) LCD not in use = when suspended (possible operator error). (PS/2) ASCII setup conflict
171 (PCC) Base 128K check= sum failure. (PS/2) Failed I/O addressing test - may be battery failure
172 (PCC) Diskette active when suspended (possible operator error). (PS/2) System Board
173 (PCC) Real-time clock= RAM verification error. (PS/2) CMOS checksum error (Run SETUP)
174 (PCC) LCD configurati= on changed (possible operator error). (PS/2) Bad configuration (Run SETUP= )
175 (PS/2) Security error= - the system board EEPROM failed
176 (PS/2) Security error= - the tamper-evident switch was tripped. This usually means that the cov= ers were removed without using a key
177 (PS/2) Security error= - passwords corrupted
178 (PS/2) Security error= - passwords corrupted
179 (PS/2) The system err= or log is full -- clear the error log
181 (PS/2) Boot error - no RIPL adapter or SCSI hard disk (ID 6) found
182 (PS/2) Privileged-acc= ess password jumper in wrong position
183 (PS/2) Must enter Privileged-access password, not power-on password
184 (PS/2) The power-on password is corrupted
185 (PS/2) The selectable startup sequence is corrupted
186 (PS/2) Security error=
187 (PS/2) Vital Product = Data (VPD) error - system serial number corrupt
188 (PS/2) VPD error -- r= un Automatic Configuration
189 (PS/2) The wrong pass= word was entered 3 times. Clear the system error log and restart the system= .
190 (PS/2) System board e= rror
191 (PS/2) Failed 82385 c= ache test
192 (N51) Lid switch erro= r. (Thinkpad) Voltage converter error
193 (PS/2) System board memory error
194 (PS/2) System board memory error or riser error (model 90)
199 User indicated configuration not correct.
201 Memory test failed. T= he ERROR shows the bank number in the leading characters. 5150/4450

(PC-1) Failing Memory Module Bit/Bank Location: 16-64K planar.
Code: xyzz 201

If x=3D0, then the failing memory is on the planar
For x=3D0, y=3D0 -= > Bank 0 (row closest to the expansion card slots).
For x=3D0, y=3D4 -= > Bank 1 (2nd row from the expansion card slots).
For x=3D0, y=3D8 -= > Bank 2 (3rd row from the expansion card slots).
For x=3D0, y=3DC -= > Bank 3 (row closest to the speaker connector).
zz=3D00 -> Pari= ty Bit - chip on the left side of planar (keyboard connector is on top).
zz=3D01 -> Bit = 0 - chip to right of Parity Bit.
zz=3D02 -> Bit = 1 - chip to right of Bit 0.
zz=3D04 -> Bit = 2 - chip to right of Bit 1.
zz=3D08 -> Bit = 3 - chip to right of Bit 2.
zz=3D10 -> Bit = 4 - chip to right of Bit 3.
zz=3D20 -> Bit = 5 - chip to right of Bit 4.
zz=3D40 -> Bit = 6 - chip to right of Bit 5.
zz=3D80 -> Bit = 7 - chip to right of Bit 6

(PC-2) Failing Memory Module Bit/Bank Locatio= n: 64-256K planar
Code: xyzz 201

If x=3D0-3, then t= he failing memory is on the planar
for x=3D0-3, y=3D0= -> Bank 0 (row closest to the expansion card slots)
for x=3D0-3, y=3D1= -> Bank 1 (2nd row from the expansion card slots)
for x=3D0-3, y=3D2= -> Bank 2 (3rd row from the expansion card slots)
for x=3D0-3, y=3D3= -> Bank 3 (row closest to the speaker connector)

The zz codes are exactly the same as the PC-1 mapping

5160/5155/XT370/5531/4455 Failing Memory Modu= le Bit/Bank Location:
(64-256K planars OR 256-640K planars)
Code: xbbbb zz 201

If x=3D0-3, then t= he failing memory is on the planar

The zz codes are exactly the same as the PC-1 mapping

20NxP (PS/2) if the P digit/letter is in the range "G" to "V", the proce= ssor board is probably bad (model 90/95).
N points to the likely failing SIMM, P is the size/speed detected

For:
N=3D1 Socket Unknown
N=3D2 Suspect Socket A1
N=3D3 Suspect Socket B1
N=3D4 Suspect Socket A2
N=3D5 Suspect Socket B2
N=3D6 Suspect Socket A3
N=3D7 Suspect Socket B3
N=3D8 Suspect Socket A4
N=3D9 Suspect Socket B4

For:
P=3D0 Size/Speed Unknown
P=3D4 4MB, 85ns memory
P=3D5 2MB, 85ns memory
P=3D6 1MB, 85ns memory
P=3D8 8MB, 80ns memory
P=3D9 2MB, 80ns memory
P=3DA 8MB, 80ns memory
P=3DB 8MB, 70ns memory
P=3DC 2MB, 70ns memory

201 (PS/2) Data miscompar= e, parity error or bad adapter. PCC - Memory pattern test failure
202 (PS/2) Memory address error. PCC - Memory address test failure
203 (PS/2) Memory address error or refresh failure
204 (PS/2) Relocated memo= ry (run diagnostics again)
205 (PS/2) CMOS error
207 (PS/2) ROM failure
210 (PS/2) Parity error in base 64K. NOTE: "0002102C 00000" is basically a "210&qu= ot; error code, which is a memory
error on the planar. The "2C" should be interpreted as: 2 - Planar SIMM socket B1 (on= a 90 that's in J3 on the card in J11), C - Parity type SIMM, 2 Meg, 70 n= s
211 (PS/2) Base 64k on I/O channel failed. 00021100 I/O channel check. 00021400 single bit error =
214 (PS/2) Probable memory error, may be system/processor board
215 (PS/2) Base 64k on daughter card 2 card failed. On a PS/2 Mod 80 if you remove the memory card from a configured system and plug it into the 'other' slot (eithe= r by mistake or deliberately), you will get a 215/216 error during POST. You will not be able to run SETUP. Fix the problem by moving the card back= to the other slot. If you really want to change the position, you will ei= ther have to disconnect the battery (for a long time) or configure the mach= ine with TWO memory cards and then remove the one that you don't want and reconfigure it with one again.
216 (PS/2) Base 64k on daughter card 1 card failed -- See comment on 215 above
217 (PS/2) Multibit ECC e= rror
221 Machine error when copying the BIOS into RAM (8580-111 only). ROM to RAM remap error. An error occurred when the system checked the 128KB that was to accept a = copy of the ROM. This is a latching error; once the error is detected, the system will no longer try to move the ROM to RAM until diagnostics (SE= TUP) are run to clear the error.
225 Some of your memory m= ay be defective or not fast enough for your machine.
226 (PS/2) Memory error <= /li>
231 EMO memory error indicating either a defective 80386 Memory Expansion Option card or defective memory module(s) on the EMO card.
235 (PS/2) Probable memory error, may be system/processor board
240 (PS/2) Memory error <= /li>
241 Incompatible or unrecognized memory module installed on 80386 Memory Expansion Option. Unsupported SIMM. The 1M SIMM from the model 70 planar is not supported because it is too slow.
251 Location of memory modules or amount of memory installed on 80386 Memory Expansion Option card has been changed. System must be reconfigured.
255 (PS/2) Memory error <= /li>
290 (PS/2) Unsupported me= mory combination detected
291 (PS/2) Checksum value mismatch
292 (PS/2) Checksum value mismatch
293 (PS/2) Checksum value mismatch
294 (PS/2) Checksum value mismatch
295 (PS/2) Check memory f= or an unsupported configuration or modules
296 (PS/2) Check memory f= or an unsupported configuration or modules
298 (PS/2) Checksum value mismatch
301 Keyboard did not resp= ond to software reset correctly or a stuck key failure was detected. If a stuck key was detected, the scan code for the key is displayed (as "301 xx" or "xx-0301").
301 (PCC) xx Stuck key detected (xx indicates internal scan code). (PS/2) Keyboard error -- replace if same error with DIAGNOSTICS
302 User indicated error = from the keyboard test.
303 (PS/2) Keyboard or sy= stem board error. PCC - Keyboard controller failure
304 (PS/2) System board error. PCC - Keyboard cable not attached
305 (PS/2) Keyboard +5v e= rror or external keypad error
306 (PS/2) Unsupported Keyboard
307 (PS/2) Unsupported keyboard or auxiliary input device
308 (PS/2) Bad numeric ke= ypad or system board
324 Replace portion of keyboard cable between system unit and screw coupling
345 (No definition provid= ed). On a 3270PC AT which generated 345s on POSTs (only when warm), the CE replaced the driver board for the keyboard which cured the problem.
365 KEYBOARD Replace Keyb= oard
366 KEYBOARD Replace Interface Cable
367 KEYBOARD Replace Enhancement Card or Cable
401 Monochrome memory tes= t, horizontal sync frequency test, or video test failed. PS/2 - CRT error= or parallel port error -- call out System Board
408 User indicated display attributes failure.
416 User indicated charac= ter set failure.
424 User indicated 80X25 = mode failure.
432 Parallel port test fa= iled ( monochrome adapter ).
5xx (PCC) Color/graphics adapter failure (Not within system unit)
501 Color memory test fai= led, horizontal sync frequency test, or video test failed. PS/2 - CRT error=
508 User indicated display attribute failure.
516 User indicated charac= ter set failure.
524 User indicated 80x25 = mode failure.
532 User indicated 40x25 = mode failure.
540 User indicated 320x200 graphics mode failure.
548 User indicated 640x200 graphics mode failure.
556 COLOR ADAPTER Light p= en test failed.
564 COLOR ADAPTER User indicated screen paging test failure.
601 Diskette power on diagnostics test failed. PS/2 - Diskette drive or controller error. PC= C - Diskette controller or drive failure
602 Diskette test failed. PS/2 - Diskette boot record error
604 Non-Media Sense Diske= tte Drive Installed
604 (PS/2 M57) 1.2M floppy disk drive interface pin 4, 9, 17, or 27 is either grounded or driven = low when all drives are de-selected
606 Diskette verify funct= ion failed.
607 Write protected diske= tte.
608 Bad command diskette status returned.
610 Diskette initializati= on failed.
611 Timeout - diskette st= atus returned.
612 Bad NEC - diskette st= atus returned.
613 Bad DMA - diskette st= atus returned.
614 DISKETTE DMA boundary software problem.
621 Bad seek - diskette s= tatus returned.
622 Bad CRC - diskette st= atus returned.
623 Record not found - diskette status returned.
624 Bad address mark - diskette status returned.
625 Bad NEC seek - disket= te status returned.
626 Diskette data compare error.
627 DISKETTE Diskette line change error
628 DISKETTE Diskette rem= oved (invalid media type)
630 (PS/2) Index stuck HI (drive A)
631 (PS/2) Index stuck LO (drive A)
632 (PS/2) Track 0 stuck = off (drive A)
633 (PS/2) Track 0 stuck = on (drive A)
640 (PS/2) Index stuck HI (drive B)
641 (PS/2) Index stuck LO (drive B)
642 (PS/2) Track 0 stuck = off (drive B)
643 (PS/2) Track 0 stuck = on (drive B)
650 (PS/2) Drive speed er= ror
651 (PS/2) Format failure=
652 (PS/2) Verify failure=
653 (PS/2) Read failure <= /li>
654 (PS/2) Write failure =
655 (PS/2) Controller err= or
656 (PS/2) Drive failure =
657 (PS/2) Write protect stuck (protected)
658 (PS/2) Change line st= uck (changed)
659 (PS/2) Write protect stuck (unprotected)
660 (PS/2) Change line st= uck (unchanged)
662 (PS/2) Wrong diskette= type installed or drive or cable failure
663 (PS/2) Wrong media ty= pe in drive
670 (PS/2) System board, drive or cable failure
675 (PS/2) System board, drive or cable failure
7xx Math Coprocessor or system board failure
701 Math Coprocessor Fail= ure -- replace Coprocessor
701 (PS/2) Math Coprocess= or Presence Initialization
702 (PS/2) 80387 math coprocessor exception errors test
703 (PS/2) 80387 math coprocessor rounding test
704 (PS/2) 80387 math coprocessor arithmetic test 1
705 (PS/2) 80387 math cop= rocessor arithmetic test 2
706 (PS/2) 80387 math coprocessor arithmetic test 3 (80387 only)
707 (PS/2) 80387 math coprocessor combination test
708 (PS/2) 80387 math coprocessor integer/store test
709 (PS/2) 80387 math coprocessor equivalent expressions
710 (PS/2) 80387 math coprocessor exceptions (interrupts)
711 (PS/2) 80387 math coprocessor save state (FSAVE)
712 (PS/2) 80387 math coprocessor protected mode test
713 (PS/2) 80387 math coprocessor special test (voltage/temp sensitive)
901 Printer adapter data register latch error.
902 Printer adapter contr= ol register latch error.
903 Printer adapter regis= ter address decode error.
904 Printer adapter addre= ss decode error.
910 Status line(s) WRAP connector error. (PN 8529228 ?)
911 Status line bit 7 wrap error.
912 Status line bit 7 wrap error.
913 Status line bit 6 wrap error.
914 Status line bit 5 wrap error.
915 Status line bit 4 wrap error.
916 Printer adapter inter= rupt wrap failed.
917 Unexpected printer adapter interrupt.
92x Feature register erro= r. (Special card.)
10xx Reserved for parallel printer adapter.
1001 Parallel printer ada= pter -- Adapter test failed.
1014 Parallel printer ada= pter -- Conflict between 2 adapters.
1054 Either wrong switch settings or a "201" memory error
1101 Asynchronous communications adapter test failed. When testing the XT/286 - AT parallel/serial adapter with Advanced Diagnostics version 2.04, you MU= ST have the new style wrap connector (or 'pig-tail'). Version 2.04 uses another scheme of wrapping the data and control lines on the serial po= rt. If you do not have the new wrap connector, use version 2.03
1101 (PS/2) 16550 async c= hip error or POST error. (PCC) RS-232 communication adaptor COM1 failure (= Not within system unit). 8250 function or modem failure
1102 (PS/2) Card selected feedback error. (PCC) Internal modem failure
1103 (PS/2) Port 102H register test failure
1106 (PS/2) Serial option= can not be put to sleep
1107 (PS/2) Cable error <= /li>
1108 (PS/2) Async IRQ3 er= ror
1109 (PS/2) Async IRQ4 er= ror
1110 ASYNC Modem Status Register not clear. (PS/2) 16550 async chip register failure
1111 ASYNC Ring Indicate failure. (PS/2) Internal wrap test of 16550 modem control line failure=
1112 ASYNC Trailing Edge = Ring indicate failure. (PS/2) External wrap test of 16550 modem control line failure
1113 ASYNC Receive and De= lta Receive line signal detect failure. (PS/2) 16550 transmit error
1114 ASYNC Receive line signal detect failure. (PS/2) 16550 receive error
1115 ASYNC Delta Receive = line signal detect failure. (PS/2) 16550 receive error data not equal trans= mit data
1116 ASYNC Line Control Register (all bits cannot be set). (PS/2) 16550 interrupt function err= or
1117 ASYNC Line Control Register (all bits cannot be reset). (PS/2) 16550 fails baud rate test=
1118 ASYNC Transmit holdi= ng and/or shift register stuck on. (PS/2) 16550 interrupt driven receive external data wrap test failure
1119 ASYNC Data Ready stu= ck on. (PS/2) 16550 FIFO error
1120 ASYNC Interrupt Enab= le Register (all bits cannot be set)
1121 ASYNC Interrupt Enab= le Register (all bits cannot be reset)
1122 ASYNC Interrupt pend= ing stuck on
1123 ASYNC Interrupt ID register stuck on
1124 ASYNC Modem Control Register (all bits cannot be set)
1125 ASYNC Modem Control Register (all bits cannot be reset)
1126 ASYNC Modem Status Register (all bits cannot be set)
1127 ASYNC Modem Status Register (all bits cannot be reset)
1128 ASYNC Interrupt ID Failure
1129 ASYNC Cannot force overrun error
1130 ASYNC No Modem Status Interrupt
1131 ASYNC Invalid Interr= upt status pending
1132 ASYNC No data ready =
1133 ASYNC No data availa= ble Interrupt
1134 ASYNC No Transmit Holding Interrupt
1135 ASYNC No Interrupts =
1136 ASYNC No Receive Line Status Interrupt
1137 ASYNC No Receive data available
1138 ASYNC Transmit Holdi= ng Register not empty
1139 ASYNC No Modem Status Interrupt
1140 ASYNC Transmit Holdi= ng Register not empty
1141 ASYNC No Interrupts =
1142 ASYNC NO IRQ4 Interr= upt
1143 ASYNC No IRQ3 Interr= upt
1144 ASYNC No Data Transferred
1145 ASYNC Max Baud rate failed
1146 ASYNC Min Baud rate failed
1148 ASYNC Timeout Error =
1149 ASYNC Invalid Data Returned
1150 ASYNC Modem Status Register error
1151 ASYNC No DSR to Delta DSR. Errors will occur if a down level serial wrap plug (p/n 8529280) = or (p/n 1501873) is used with Advanced Diagnostics 2.04 or higher. Use 25= pin wrap plug p/n 62x1083
1152 ASYNC No Data Set Re= ady
1153 ASYNC No Delta
1154 ASYNC Modem Status Register not clear
1155 ASYNC No CTS and Del= ta CTS
1156 ASYNC No Clear to Se= nd
1157 ASYNC No delta CTS. =
1201 Alternate Asynchrono= us communications adapter test failed. (PS/2) Can not detect presence of = dual async adapter. (PCC) RS-232 communication adaptor COM2 failure (Not wi= thin system unit)
1202 (PS/2) Dual async adapter card selected feedback error
1203 (PS/2) Dual async adapter port 102H register test failure
1206 (PS/2) Dual async adapter serial option can not be put to sleep
1207 (PS/2) Dual async adapter cable error
1208 (PS/2) Dual async adapter async IRQ3 error
1209 (PS/2) Dual async adapter async IRQ4 error
1210 ALT ASYNC Modem Stat= us Register not clear. (PS/2) 16550 async chip register failure
1211 ALT ASYNC Ring Indic= ate failure. (PS/2) Internal wrap test of 16550 modem control line failure=
1212 ALT ASYNC Trailing E= dge Ring indicate failure. (PS/2) External wrap test of 16550 modem control line failure
1213 ALT ASYNC Receive and Delta Receive line signal detect failure. (PS/2) 16550 transmit error =
1214 ALT ASYNC Receive li= ne signal detect failure. (PS/2) 16550 receive error
1215 ALT ASYNC Delta Rece= ive line signal detect failure. (PS/2) 16550 receive error data not equal transmit data
1216 ALT ASYNC Line Contr= ol Register (all bits cannot be set). (PS/2) 16550 interrupt function err= or
1217 ALT ASYNC Line Contr= ol Register (all bits cannot be reset). (PS/2) 16550 fails baud rate test=
1218 ALT ASYNC Transmit holding and/or shift register stuck on. (PS/2) 16550 interrupt driven receive external data wrap test failure
1219 ALT ASYNC Data Ready stuck on. (PS/2) 16550 FIFO
1220 ALT ASYNC Interrupt Enable Register (all bits cannot be set)
1221 ALT ASYNC Interrupt Enable Register (all bits cannot be reset)
1222 ALT ASYNC Interrupt pending stuck on
1223 ALT ASYNC Interrupt = ID register stuck on
1224 ALT ASYNC Modem Cont= rol Register (all bits cannot be set)
1225 ALT ASYNC Modem Cont= rol Register (all bits cannot be reset). (PS/2) 16550 async chip register failure
1226 ALT ASYNC Modem Stat= us Register (all bits cannot be set). (PS/2) Internal wrap test of 16550 modem control line failure
1227 ALT ASYNC Modem Stat= us Register (all bits cannot be reset). (PS/2) External wrap test of 16550 modem control line failure
1228 ALT ASYNC Interrupt = ID Failure. (PS/2) 16550 transmit error
1229 ALT ASYNC Cannot for= ce overrun error. (PS/2) 16550 receive error
1230 ALT ASYNC No Modem Status Interrupt. (PS/2) 16550 receive error data not equal transmit d= ata
1231 ALT ASYNC Invalid Interrupt status pending. (PS/2) 16550 interrupt function error
1232 ALT ASYNC No data re= ady. (PS/2) 16550 fails baud rate test
1233 ALT ASYNC No data available Interrupt. (PS/2) 16550 interrupt driven receive external da= ta wrap test failure
1234 ALT ASYNC No Transmit Holding Interrupt. (PS/2) 16550 FIFO
1235 ALT ASYNC No Interru= pts
1236 ALT ASYNC No Receive= Line Status Interrupt
1237 ALT ASYNC No Receive data available
1238 ALT ASYNC Transmit Holding Register not empty
1239 ALT ASYNC No Modem Status Interrupt
1240 ALT ASYNC Transmit Holding Register not empty
1241 ALT ASYNC No Interru= pts
1242 ALT ASYNC NO IRQ4 Interrupt
1243 ALT ASYNC No IRQ3 Interrupt
1244 ALT ASYNC No Data Transferred
1245 ALT ASYNC Max Baud r= ate failed
1246 ALT ASYNC Min Baud r= ate failed
1248 ALT ASYNC Timeout Er= ror
1249 ALT ASYNC Invalid Da= ta Returned
1250 ALT ASYNC Modem Stat= us Register error
1251 ALT ASYNC No DSR to Delta DSR
1252 ALT ASYNC No Data Set Ready
1253 ALT ASYNC No Delta <= /li>
1254 ALT ASYNC Modem Stat= us Register not clear
1255 ALT ASYNC No CTS and Delta CTS
1256 ALT ASYNC No Clear to Send
1257 ALT ASYNC No delta C= TS
1290 (PS/2) Cached Proces= sor Option - Disk cache error
1301 Game control adapter test failed
1302 Joystick test failed=
1380 Error on a Games Ada= pter -- remove adapter and re-run autoconfig
1401 Printer test failed. PS/2 - Printer failure
1402 Printer NOT READY er= ror. PS/2 - Printer not ready error
1403 Printer NO PAPER err= or. PS/2 - Interrupt failure or out of paper
1404 (PS/2) System board = time out
1405 (PS/2) Parallel adap= ter failure
1406 (PS/2) Presence test failed
15xx SDLC communications adapter errors.
1510 8255 port B failure.=
1511 8255 port A failure.=
1512 8255 port C failure.=
1513 8253 timer 1 did not reach terminal count.
1514 8253 timer 1 stuck o= n.
1515 8253 timer 0 did not reach terminal count.
1516 8253 timer 0 stuck o= n.
1517 8253 timer 2 did not reach terminal count.
1518 8253 timer 2 stuck o= n.
1519 8273 port B error. <= /li>
1520 8273 port A error. <= /li>
1521 8273 command/read timeout.
1522 Interrupt level 4 failure.
1523 Ring Indicate stuck = on.
1524 Receive clock stuck = on.
1525 Transmit clock stuck= on.
1526 Test indicate stuck = on.
1527 Ring indicate not on= .
1528 Receive clock not on= .
1529 Transmit clock not o= n.
1530 Test indicate not on= .
1531 Data set ready not o= n.
1532 Carrier detect not o= n.
1533 Clear to send not on= .
1534 Data set ready stuck= on.
1536 Clear to send stuck = on.
1537 Level 3 interrupt failure.
1538 Receive interrupt results error.
1539 Wrap data miscompare= .
1540 DMA channel 1 error.=
1541 DMA channel 1 error.=
1542 Error in 8273 error checking or status reporting.
1547 Stray interrupt leve= l 4
1548 Stray interrupt leve= l 3
1549 Interrupt presentati= on sequence timeout.
1604 DSEA (Display Station Emulator Adapter) adapter error or twinax problem
1608 DSEA Adapter error, = or twinaxial problem
1624 DSEA Adapter error. =
1634 DSEA Adapter error. =
1644 DSEA Adapter error. =
1652 DSEA Adapter error. =
1654 DSEA Adapter error. =
1658 DSEA Adapter error. =
1664 DSEA Adapter error. =
1662 DSEA Interupt Level switches set incorrectly or DSEA Adapter error.
1668 DSEA Interupt Level switches set incorrectly or DSEA Adapter error.
1674 DSEA Station address error or DSEA Adapter error.
1684 DSEA Feature not installed or Device address switches set incorrectly.
1688 DSEA Feature not installed or Device address switches set incorrectly.
17xx Fixed Disk errors. <= /li>
1701 PC Fixed disk drive = not ready or PCAT Hardfile adapter test failed
1702 Fixed disk adapter e= rror - Time out. Either the controller card or the drive will have to be replaced. Try a new card first since that doesn't usually result in da= ta loss on the original drive.
1703 Fixed disk drive err= or - Seek failure
1704 Fixed disk adapter or drive error - Hardfile controller error
1705 Record not found
1706 Write failure -- Wri= te Fault Error
1707 Bad track 0
1708 Bad reset -- Head Se= lect Error
1709 Disk 0 error -- AT f= ixed disk - ECC error
1710 Drive not ready -- R= ead Buffer Overrun
1711 Bad Address Mark -- = AT fixed disk
1712 Internal controller diagnostics fail. Make sure Adv. Diags. were loaded from cold boot (51= 70 PC/AT only) 20 meg or larger disk connected to J3 -- "standard&qu= ot; IBM controller supplied with Expansion Unit does not support drives la= rger than 10meg.
1713 DMA boundary error -- Data Compare Error
1714 POST hardfile test f= ails -- Drive Not Ready
1715 Track 0 indicator failure. 20 meg or larger disk connected to J2 -- see 1712 above
1716 CE track bad
1717 Surface read errors =
1718 Bad hard file type <= /li>
1726 Data compare error <= /li>
1730 Replace Adapter
1731 Replace Adapter
1732 Replace Adapter
1733 BIOS undefined error return
1735 Bad command
1736 Data corrected error=
1737 Bad track
1738 Bad sector
1739 Bad initialization <= /li>
1740 Bad sense
1750 (PS/2) Drive "x" verify failure
1751 (PS/2) Drive "x" read failure
1752 (PS/2) Drive "x" write failure
1753 (PS/2) Drive "x" random read test error
1754 (PS/2) Drive "x" seek test error
1755 (PS/2) Controller failure
1756 (PS/2) Controller ECC test failure
1757 (PS/2) Controller he= ad select failure
1780 Time out for hard dr= ive 0 at IPL -- No IPL Capability - Try formatting
1781 Time out for hard dr= ive 1 at IPL -- Try formatting
1780/1 means FDISK and DOS format are required.
1782 Fixed disk controller error
1790 Fixed disk 0 error -- Check hard disk cable connection -- Press F1
1791 Fixed disk 1 error -- Check hard disk cable connection -- Press F1
1790/1 usually indicates = low level format is required
18xx I/O Expansion unit errors.
1801 I/O Expansion unit P= OST error.
1803 (PS/2) System board failure on 8556 or 8557 machines
181x Expansion unit driver card errors -- SU end
1810 Enable/Disable failu= re.
1811 Extender card wrap t= est failed (disabled).
1812 High order address l= ines failure (disabled).
1813 Wait state failure (disabled).
* 1813 and 1815 * There i= s an EC to the expansion card which resides in the system unit. The modification is in the upper left hand corner (component side); one tr= ace is cut on the printed side and one wire add component side.
1814 Enable/Disable could= not be set on.
1815 Wait state failure (enabled) -- See 1813 note above
1816 Extender card wrap t= est failed (enabled).
1817 High order address l= ines failure (enabled).
1818 Disable not function= ing
1819 Wait request switch = not set correctly. This error condition is noted whenever either (1) there= is RAM in the SU 64K or more above the EU Switch setting or (2) if EU switches are set for more than 640K. DMA errors can result if there is= any SU RAM above the switch settings. Put all memory and memory expansion cards in the system unit with the display adapters and the async adapt= er in the expansion box. Also see REPAIR PROBLEM forum. SU switch setting= s of OFF ON OFF ON (640K) are fine for all normal system configurations including configurations of less than 640K.
182x Expansion unit recei= ver card errors -- EU end
1820 Receiver card wrap t= est failure ...or could be a power supply failure
1821 Receiver high order address lines failure
186x (PS/2) Set Configura= tion error -- replace battery
20xx Bisync communications adapter errors. (PS/2) - Model 90/95 video memory failure
2003 Associated with Music Feature card -- may be software error
2010 8255 port a failure =
2011 8255 port b failure =
2012 8255 port c failure =
2013 8253 timer 1 did not reach terminal count
2014 8253 timer 1 stuck o= n
2016 8253 timer 2 did not reach terminal count or timer 2 stuck on.
2017 8251 Data set ready failed to come on
2018 8251 Clear to send n= ot sensed
2019 8251 Data set ready stuck on
2020 8251 Clear to send s= tuck on
2021 8251 hardware reset failed
2022 8251 software reset failed
2023 8251 software "error reset" failed
2024 8251 transmit ready = did not come on
2025 8251 receive ready d= id not come on
2026 8251 could not force "overrun" error status
2027 Interrupt failure-no timer interrupt
2028 Interrupt failure-tr= ansmit, replace card or planar
2029 Interrupt failure-transmit, replace card
2030 Interrupt failure-receive, replace card or planar
2031 Interrupt failure-receive, replace card
2033 Ring indicate stuck = on
2034 Receive clock stuck = on
2035 Transmit clock stuck= on
2036 Test indicate stuck = on
2037 Ring indicate stuck = on
2038 Receive clock not on=
2039 Transmit clock not o= n
2040 Test indicate not on=
2041 Data set ready not o= n
2042 Carrier detect not o= n
2043 Clear to send not on=
2044 Data set ready stuck= on
2045 Carrier detect stuck= on
2046 Clear to send stuck = on
2047 Unexpected transmit interrupt
2048 Unexpected receive interrupt
2049 Transmit data did not equal receive data
2050 8251 detected overrun error
2051 Lost data set ready during data wrap
2052 Receive timeout duri= ng data wrap
21xx Alternate bisync communications adapter errors
2110 8255 Port A failure =
2111 8255 Port B failure =
2112 8255 Port C failure =
2113 8253 Timer 1 did not reach terminal count
2114 8253 Timer 1 stuck o= n
2116 8253 Timer 2 did not reach terminal count or
2117 8251 Date set ready failed to come on
2117 8251 Clear to send n= ot sensed
2118 8251 Data set ready stuck on
2119 8251 Clear to send s= tuck on
2120 8251 Hardware reset failed
2121 8251 Software reset failed
2122 8251 Software "error reset" failed
2123 8251 Transmit ready = did not come on
2124 8251 Receive ready d= id not come on
2125 8251 Could not force "overrun" error status
2126 Interrupt failure-no timer interrupt
2128 Interrupt failure-tr= ansmit, replace card or
2129 Interrupt failure-transmit, replace card
2130 Interrupt failure-receive, replace card or planar
2131 Interrupt failure-receive, replace card
2133 Ring indicate stuck = on
2134 Receive clock stuck = on
2135 Transmit clock stuck= on
2136 Test indicate stuck = on
2137 Ring indicate stuck = on
2138 Receive clock not on=
2139 Transmit clock not o= n
2140 Test indicate not on=
2141 Data set ready not o= n
2142 Carrier detect not o= n
2143 Clear to send not on=
2144 Data set ready stuck= on
2145 Carrier detect stuck= on
2146 Clear to send stuck = on
2147 Unexpected transmit interrupt
2148 Unexpected receive interrupt
2149 Transmit data did not equal receive data
2150 8251 detected overrun error
2151 Lost data set ready during data wrap
2152 Receive timeout duri= ng data wrap
22xx Cluster Adapter -- Problem is in Cluster Adapter, System Board or Power Supply
2201 Cluster Adapter Fail= ure
23xx Plasma Monitor Adapt= er
24xx EGA or VGA or L40SX = LCD display
2401 Enhanced Grahpics Adapter Failure
2401 (PS/2) Planar video error -- it can be the display or the video. First check for a solid connection -- wiggle the plug at the system end and check for one or m= ore bent pins. Next swap the monitor. If a 2401 error persists after swapp= ing the monitor, then the system board should be replaced next. However if your monitor serial number starts with "72" , is below 72-0374000 and you cannot find the number "61" stamped on the bottom of the display (you may need to remove the display stand), then= a replacement monitor will probably fix this error. If it's definitely on the planar (ie another monitor fails) check the Inmos palette DAC (cer= amic DIP module with gold colored middle) for shorts between the pins.
2402 (PS/2) Diagnostic vi= deo error
2408 (PS/2) VGA Ground Circuit Fault -- cord may be disconnected at system end
2409 (PS/2) VGA Ground Circuit Fault -- may be related to 8602 error. FIRST, check that you h= ave DASDDRVR in config.sys. Then replace display; if failure repeats during video diagnostics, replace the system board.
2410 (PS/2) Replace System Board
2601-2655 XT/370-M CARD P-Processor
2657-2668 XT/370-M CARD M-Memory
2672 XT/370-M CARD EM-Emulator
2673-2674 XT/370-P CARD <= /li>
2677-2680 XT/370-P CARD <= /li>
2681 XT/370-M CARD
2682-2694 XT/370-P CARD <= /li>
2697 XT/370-P CARD
2698 DIAGNOSTIC DISKETTE ERROR
2701-2703 XT/370-EM CARD =
2801 3278/79 Emulation DF= CA Card -- Unplug coax before running diagnostics
2801 (PS/2) 3270 Adapter keystroke accepted status bit failure
2802 (PS/2) Reset decoded status bit failure
2803 (PS/2) Cursor low reg incorrect on reset
2804 (PS/2) Cursor high r= eg incorrect on reset
2805 (PS/2) RAM buffer ri= pple pattern incorrect on reset
2806 (PS/2) No por status= on poll after reset
2807 (PS/2) Status not cl= ear on poll ack
2808 (PS/2) Terminal id r= eg write/read test failed
2809 (PS/2) Not busy stat= us bit not working
2810 (PS/2) Address count= er low incorrect
2811 (PS/2) Cursor low reg incorrect
2812 (PS/2) Address count= er high incorrect
2813 (PS/2) Cursor high r= eg incorrect
2814 (PS/2) Buffer being modified bit off during write command
2815 (PS/2) Base buffer modified complete not set by write command
2816 (PS/2) Write command/read command results not comparing
2817 (PS/2) Buffer being modified off during clear command
2818 (PS/2) Base buffer modified complete not set by clear command
2819 (PS/2) No op complete status after clear command
2820 (PS/2) Wrong area cleared by clear command
2821 (PS/2) Correct area = not cleared by clear command
2822 (PS/2) Correct area = not cleared by clear command
2823 (PS/2) Stopping addr= ess not correct after clear command
2824 (PS/2) Stopping addr= ess not correct after clear command
2825 (PS/2) Correct area = not cleared by clear command
2826 (PS/2) Wrong area cleared by clear command
2827 (PS/2) Stopping addr= ess not correct after clear command
2828 (PS/2) Stopping addr= ess not correct after clear command
2829 (PS/2) Correct area = not cleared by clear command
2830 (PS/2) Wrong area cleared by clear command
2831 (PS/2) Buffer being modified off during insert command
2832 (PS/2) Base buffer modified complete not set by insert command
2833 (PS/2) No op complete status after insert command
2834 (PS/2) Wrong data disturbed by insert command
2835 (PS/2) Byte inserted= at wrong address by insert command
2836 (PS/2) Data shifted incorrectly by insert command
2837 (PS/2) Shifting not stopped by null during insert command
2838 (PS/2) Byte at wrong address after insert command
2839 (PS/2) Data shifted incorrectly by insert command
2840 (PS/2) Shifting not stopped by attribute on insert command
2841 (PS/2) Address count= er not correct after search forward command
2842 (PS/2) Cursor reg incorrect after search forward command
2843 (PS/2) No op complete status after search forward command
2844 (PS/2) Address count= er not correct after search forward command
2845 (PS/2) Cursor reg incorrect after search forward command
2846 (PS/2) Address count= er not correct after search backward command
2847 (PS/2) Cursor reg incorrect after search backward command
2848 (PS/2) No op complete after seach backward command
2849 (PS/2) Address count= er incorrect after search backward command
2850 (PS/2) Cursor reg incorrect after search backward command
2851 (PS/2) Load control = reg command not clearing visual/sound reg
2852 (PS/2) Load control = reg command not setting visual/sound reg
2853 (PS/2) Inhibit featu= re step not setting in visual/sound reg
2854 3278/79 (DFCA 3270) Diagnostic Incompatibility. (PS/2) Inhibit display not setting in visual/sound reg
2855 (PS/2) Inhibit cursor not setting in visual/sound reg
2856 (PS/2) Reverse cursor not setting in visual/sound reg
2857 (PS/2) Blink cursor = not setting in visual/sound reg
2858 (PS/2) Write/read of pc/il control reg incorrect
2859 3278/79 (DFCA 3270) = Possible bad BSC Card. (PS/2) Adapter does not cause interrupt when enabled
2860 (PS/2) Write/read testing of RAM buffer failed
2861 (PS/2) Polling does = not clear status reg
2862 (PS/2) Interrupt/sta= tus reg not clearing on reset under mask
2863 (PS/2) Spare command causing unexpected action
2864 (PS/2) Not used
2865 (PS/2) Page register failure
2866 (PS/2) Read multiple command failure
2867 (PS/2)
2868 (PS/2) 3287 mode fai= lure
2869 (PS/2) TCA mode fail= ure
29xx Color Printer, Paral= lel Printer Adapter, Monochrome Display and Printer Adapter, Printer Attachment Cable, System Board, Power Supply
2901 Color Graphics print= er tests failed
30xx Primary PC Network Adapter Error
3001 LAN Network Adapter = CPU Failure -- Replace Primary Lan Adapter
3002 LAN Network ROM Fail= ure -- Replace Primary LAN Adapter
3003 LAN Network I. D. Failure -- Replace Primary LAN Adapter
3004 LAN Network RAM Fail= ure -- Replace Primary LAN Adapter
3005 LAN Network Host Interrupt Failure -- Replace Primary LAN Adapter
3006 LAN Network + or NEG= 12V DC Failure -- Replace Primary LAN Adapter
3007 LAN Network Digital = Wrap Failure -- Replace Primary LAN Adapter
3008 LAN Network Host Interrupt Failure -- Replace Primary LAN Adapter
3009 LAN Network Sync Fai= lure -- Replace Primary LAN Adapter
3010 LAN Network Time Out Failure -- Replace Primary LAN Adapt
3011 LAN Network Time Out Failure -- Replace Primary LAN Adapter
3012 LAN Network Adapter Failure -- Card not present -- Replace Pri LAN Adpt
3013 LAN Network Digital Failure -- Replace Primary LAN Adapter
3014 LAN Network Digital Failure -- Replace Primary LAN Network Adapt er
3015 LAN Network Analog Failure (RF -- Adapter not hooked to translator) -- (Coax unplugged? -= - no signal present) You have either a PC-Net or Token Ring (or some other networking) card installed which is PROBABLY NOT CONNECTED or the netw= ork is malfunctioning. Either remove the card or correct the network probl= em.
3020 LAN Network ROM BIOS Failure
3041 LAN Network Continuo= us RF Signal Detected
3042 LAN Network Continio= us RF Signal Sent -- Replace Primary LAN Adapter
31xx Secondary Network Adapter Error
3101 ALT LAN NETWORK Adap= ter CPU Failure -- Replace Alt. Lan Adapter
3102 ALT LAN NETWORK ROM Failure -- Replace Alt. LAN Adapter
3103 ALT LAN NETWORK I. D. Failure -- Replace Alt. LAN Adapter
3104 ALT LAN NETWORK RAM Failure -- Replace Alt. LAN Adapter
3105 ALT LAN NETWORK Host Interrupt Failure -- Replace Alt. LAN Adapter
3106 ALT LAN NETWORK + or= NEG 12V DC Failure -- Replace Alt. LAN Adapter
3107 ALT LAN NETWORK Digi= tal Wrap Failure -- Replace Alt. LAN Adapter
3108 ALT LAN NETWORK Host Interrupt Failure -- Replace Alt. LAN Adapter
3109 ALT LAN NETWORK Sync Failure -- Replace Alt. LAN Adapter
3110 ALT LAN NETWORK Time= Out Failure -- Replace Alt. LAN Adapter
3111 ALT LAN NETWORK Time= Out Failure -- Replace Alt. LAN Adapter
3112 ALT LAN NETWORK Adap= ter Failure -- Replace Alt. LAN Adapter
3113 ALT LAN NETWORK Digi= tal Failure -- Replace Alt. LAN Adapter
3114 ALT LAN NETWORK Digi= tal Failure -- Replace Alt. LAN Network Adapter
3115 ALT LAN NETWORK Anal= og Failure (RF) (adapter not hooked to translator)
3120 ALT LAN NETWORK ROM = BIOS Failure
3141 ALT LAN NETWORK Continuous RF Signal Detected
3142 ALT LAN NETWORK Continious RF Signal Sent -- Replace Alt. LAN Adapter
3201 - 3250 3270 Display Adapter or Top Card Connector
3261 - 3279 Progammed Sym= bols Adapter or Top Card Connector
3280 - 3289 APA Adapter or Top Card Connector
35xx Enhanced display sta= tion emulation adapter
3504 Adapter connected on= the twinaxial cable during offline test
3508 Workstation address = in use by another workstation. Diagnostic diskette from another IBM PC was used
3509 Diagnostic program failing (Recreate Adapter Integrated Diagnostic diskette on a blank diskette).
3540 Work station address invalid, not configured at the controller. Twinaxial cable not connect= ed, or is failing. Diagnostic diskette from another IBM PC was used.
3588 Enhanced Display Sta= tion Emulation Adapter. Feature not installed or device I/O address switches set incorrectly.
3599 Diagnostic program failing (Recreate Adapter Integrated Diagnostic diskette on a blank diskette).
3601 GPIB Base Address incorrect
3602 GPIB Write to SPMR failed
3603 GPIB Write to ADR fa= iled or addressing problems
3610 GPIB Adapter cannot = be programmed to listen
3611 GPIB Adapter cannot = be programmed to talk
3612 GPIB Adapter cannot = take control with IFC
3613 GPIB Adapter cannot = go to standby
3614 GPIB Adapter cannot = take control asynchronously
3615 GPIB Adapter cannot = take control synchronously
3616 GPIB Adapter cannot = pass control
3617 GPIB Adapter cannot = be addressed to listen
3618 GPIB Adapter cannot = be unaddressed to listen
3619 GPIB Adapter cannot = be addressed to talk
3620 GPIB Adapter cannot = be unaddressed to talk
3621 GPIB Adapter unaddressable to listen with extended addressing
3622 GPIB Adapter unaddressable to listen with extended addressing
3623 GPIB Adapter unaddressable to listen with extended addressing
3624 GPIB Adapter unaddressable to listen with extended addressing
3625 GPIB Adapter cannot write to self
3626 GPIB Adapter cannot generate handshake error
3627 GPIB Adapter cannot detect DCL message
3628 GPIB Adapter cannot detect SDC message
3629 GPIB Adapter cannot detect END with EOI
3630 GPIB Adapter cannot detect EOI with EOI
3631 GPIB Adapter cannot detect END with 8 bit EOS
3632 GPIB Adapter cannot detect END with 7 bit EOS
3633 GPIB Adapter cannot detect GET
3634 GPIB Mode 3 addressi= ng not functioning
3635 GPIB Adapter cannot recognize undefined command
3636 GPIB Adapter cannot detect REM, REMC, LOK or LOKC
3637 GPIB Adapter cannot clear REM or LOK
3638 GPIB Adapter cannot detect SRQ
3639 GPIB Adapter cannot conduct serial poll
3640 GPIB Adapter cannot conduct parallel poll
3650 GPIB Adapter cannot = DMA to 7210
3651 GPIB Data error on D= MA to 7210
3652 GPIB Adapter cannot = DMA form 7210
3653 GPIB Data error on D= MA from 7210
3658 GPIB Unenvoked inter= rupt received
3659 GPIB Adapter cannot interrupt of ADSC
3660 GPIB Adapter cannot interrupt on ADSC
3661 GPIB Adapter cannot interrupt on CO
3662 GPIB Adapter cannot interrupt on DO
3663 GPIB Adapter cannot interrupt on DI
3664 GPIB Adapter cannot interrupt on ERR
3665 GPIB Adapter cannot interrupt on DEC
3666 GPIB Adapter cannot interrupt on END
3667 GPIB Adapter cannot interrupt on DET
3668 GPIB Adapter cannot interrupt on APT
3669 GPIB Adapter cannot interrupt on CPT
3670 GPIB Adapter cannot interrupt on REMC
3671 GPIB Adapter cannot interrupt on LOKC
3672 GPIB Adapter cannot interrupt on SRQI
3673 GPIB Adapter cannot interrupt terminal count on DMA to 7210
3674 GPIB Adapter cannot interrupt terminal count on DMA from 7210
3675 GPIB Spurious DMA terminal count interrupt
3697 GPIB Illegal DMA configuration setting detected
3698 GPIB Illegal interru= pt level configuration setting detected
37xx (PS/2) System board, hard disk or cable failure (refer to MAPs)
3801 Data Acquisition Ada= pter test failed
3810 Data Acquisition Tim= er read test failed
3811 Data Acquisition Tim= er interrupt test failed
3812 Data Acquisition Del= ay, BI14 test failed
3813 Data Acquisition Rat= e, BI13 test failed
3814 Data Acquisition BO1= 4, ISIRQ test failed
3815 Data Acquisition BOO, Countin test failed
3816 Data Acquisition Countout, BISTB test failed
3817 Data Acquisition BOO, BOCTS test failed
3818 Data Acquisition BO1, BIO test failed
3819 Data Acquisition BO2, BI1 test failed
3820 Data Acquisition BO3, BI2 test failed
3821 Data Acquisition BO4, BI3 test failed
3822 Data Acquisition BO5, BI4 test failed
3823 Data Acquisition BO6, BI5 test failed
3824 Data Acquisition BO7, BI6 test failed
3825 Data Acquisition BO8, BI7 test failed
3826 Data Acquisition BO9, BI8 test failed
3827 Data Acquisition BO1= 0, BI9 test failed
3828 Data Acquisition BO1= 1, BI10 test failed
3829 Data Acquisition BO1= 2, BI11 test failed
3830 Data Acquisition BO1= 3, BI12 test failed
3831 Data Acquisition BO1= 5, AICE test failed
3832 Data Acquisition BOS= TB, BOGATE test failed
3833 Data Acquisition BIC= TS, BIHOLD test failed
3834 Data Acquisition AIC= O, BI15 test failed
3835 Data Acquisition Cou= nter interrupt test failed
3836 Data Acquisition Cou= nter read test failed
3837 Data Acquisition AO0 Ranges test failed
3838 Data Acquisition AO1 Ranges test failed
3839 Data Acquisition AI0 Values test failed
3840 Data Acquisition AI1 Values test failed
3841 Data Acquisition AI2 Values test failed
3842 Data Acquisition AI3 Values test failed
3843 Data Acquisition Ana= log input interrupt test failed
3844 Data Acquisition AI23 Address or Value test failed
3901 PGA Adapter Tests fa= iled
3902 PGA Rom1 self test failure
3903 PGA Rom2 self test failure
3904 PGA Ram self test failure
3905 PGA Coldstart failure cycle power
3906 PGA Data error in communications ram
3907 PGA Address error in communications ram
3918 PGA Bad data detected while read/write to 6845 'like' registers
3909 PGA Bad data detecte= d in lower EOH bytes read/writing
3909 6845 'like' register= s
3910 PGA PGC display bank output latches
3911 PGA Basic clock fail= ure
3912 PGA Command control error
3913 PGA VSYNC scanner
3914 PGA HSYNC scanner
3915 PGA Intech failure <= /li>
3916 PGA LUT address erro= r
3917 PGA LUT red ram chip error
3918 PGA LUT green ram ch= ip error
3919 PGA LUT blue ram chip error
3920 PGA LUT data latch e= rror
3921 PGA Horizontal displ= ay failure
3922 PGA Vertical display failure
3923 PGA Light pen
3924 PGA Unexpected error=
3925 PGA Emulator address= ing error
3926 PGA Emulator data la= tch
3927 PGA Emulator ram base for error codes 27 - 30
3931 PGA Emulator H/V dis= play problem
3932 PGA Emulator cursor position
3933 PGA Emulator attribu= te display problem
3934 PGA Emulator cursor display
3935 PGA Fundamental emulation RAM problem
3936 PGA Emulation charac= ter set problem
3937 PGA Emulation graphi= cs display
3938 PGA Emulator charact= er display problem
3939 PGA Emulator bank se= lect error
3940 PGA Display ram U2 <= /li>
3941 PGA Display ram U4 <= /li>
3942 PGA Display ram U6 <= /li>
3943 PGA Display ram U8 <= /li>
3944 PGA Display ram U10 =
3945 PGA Display ram U1 <= /li>
3946 PGA Display ram U3 <= /li>
3947 PGA Display ram U5 <= /li>
3948 PGA Display ram U7 <= /li>
3949 PGA Display ram U9 <= /li>
3950 PGA Display ram U12 =
3951 PGA Display ram U14 =
3952 PGA Display ram U16 =
3953 PGA Display ram U18 =
3954 PGA Display ram U20 =
3955 PGA Display ram U11 =
3956 PGA Display ram U13 =
3957 PGA Display ram U15 =
3958 PGA Display ram U17 =
3959 PGA Display ram U19 =
3960 PGA Display ram U22 =
3961 PGA Display ram U24 =
3962 PGA Display ram U26 =
3963 PGA Display ram U28 =
3964 PGA Display ram U30 =
3965 PGA Display ram U21 =
3966 PGA Display ram U23 =
3967 PGA Display ram U25 =
3968 PGA Display ram U27 =
3969 PGA Display ram U29 =
3970 PGA Display ram U32 =
3971 PGA Display ram U34 =
3972 PGA Display ram U36 =
3973 PGA Display ram U38 =
3974 PGA Display ram U40 =
3975 PGA Display ram U31 =
3976 PGA Display ram U33 =
3977 PGA Display ram U35 =
3978 PGA Display ram U37 =
3979 PGA Display ram U39 =
3980 PGA PGC RAM timing failure
3981 PGA PGC R/W latch
3982 PGA S/R bus output latches
3983 PGA Addressing error (vertical column of memory..U2 at top)
3984 PGA Addressing error (vertical column of memory..U4 at top)
3985 PGA Addressing error (vertical column of memory..U6 at top)
3986 PGA Addressing error (vertical column of memory..U8 at top)
3987 PGA Addressing error (vertical column of memory..U10 at top)
3988 PGA Base for error c= odes 88 91 (hbank data latch errors)
3992 PGA RAS/CAS PGC fail= ure
3993 PGA Multiple write modes/nibble mask errors
3994 PGA Row nibble failu= re (display ram)
3995 PGA PGC addressing failure
44xx Display Attachment U= nit and Display
45xx IEEE Interface Adapt= er Card (IEEE-488)
46xx Artic Multiport Interface Adapter
4611 (PS/2) Multiport Interface Card
4612 (PS/2) Multiport Mem= ory Module
4613 (PS/2) Multiport Mem= ory Module
4630 (PS/2) Multiport Int= erface Card
4640 (PS/2) Multiport Mem= ory Module
4641 (PS/2) Multiport Mem= ory Module
4650 (PS/2) Multiport Interface Cable
5001 (PCC) LCD buffer fai= lure
5002 (PCC) LCD font buffer failure
5003 (PCC) LCD controller failure
5001-5019 (Thinkpad, L40,= N51) System board or LCD assembly error
5022 (Thinkpad, L40, N51) System board or LCD assembly error
5023 (Thinkpad, L40, N51) System board or LCD assembly error
5030-5033 (Thinkpad, L40, N51) System board or external display error
5037 (Thinkpad, L40, N51) System board or external display error
5038 (Thinkpad, L40, N51) External display error
5041 (Thinkpad, N51) Syst= em board, external display, or I/O panel error
5051 (Thinkpad, N51) Syst= em board or LCD components error
5062 (Thinkpad, N51) Syst= em board or LCD components error
5101 (PCC) Portable print= er interface failure
56xx Financial Communicat= ions System. FCS Input Option, FCS Output Option or FCS Security Option
5601 PS/2 keyboard failed (PORT 2) -- check connection and re-run test
5602 PS/2 Keyboard failed Self-Test -- re-run with known good keyboard. If test fails on re-run, have system unit serviced
5603 PS/2 Keyboard error = -- Invalid configuration of keyboards detected
5604 (PS/2) 50-Key keyboa= rd is not attached.
5605 (PS/2) 50-Key keyboa= rd self-test failed.
5606 (PS/2) 50 Key keyboa= rd error -- keyboard not attached
5607 (PS/2) Invalid inval= id key code -- make another selection
5608 (PS/2) 50-Key keyboa= rd error.
5609 (PS/2) Invalid system for the keyboard program.
5610 No PIN Keypad attach= ed
5611 (PS/2) PIN Keypad fa= iled -- Key code different than expected
5612 Encrypting PIN Keypad detected data of an incorrect length
5614 (PS/2) No PIN Keypad attached to System Unit.
5615 (PS/2) PIN Keypad dr= iver has an input parameter error.
Key used to cancel PIN entries has an incorrect code--Pin Pad Self Test Fail
5616 (PS/2) PIN Keypad not attached to the Pointing Device connector.
5617 (PS/2) Pin Keypad fa= iled self-test.
5618 (PS/2) Pin Keypad ha= s a communications error.
5619 (PS/2) System invalid for PIN keypad driver.
5621 (PS/2) Magnetic Stri= pe Unit failed.
5622 Magnetic Stripe reader/encoder error -- Wrong Diagnostic Diskette Level
5623 (PS/2) Magnetic Stri= pe Unit not connected to System Unit.
5624 (PS/2) Magnetic Stri= pe Unit driver input error
5625 No Magnetic Stripe device connected
5626 (PS/2) Magnetic Stri= pe Unit not attached to Pointing Device connector. Data read and data enc= oded by mag stripe device do not match
5627 (PS/2) Magnetic Stri= pe Unit self-test failed
5629 (PS/2) System invalid for the Magnetic Stripe Unit driver.
5630 (PS/2) STATUS =3D F1 system attempted unsucessful IPL from diskette.
5631 (PS/2) STATUS REMOTE START - normal start-up message.
5632 Diagnostics failed to load from diskette drive
5633 (PS/2) STATUS REMOTE= IPL - normal start-up message.
5634 Remote ipl error bet= ween 4700 PC and controller
5641 Financial Input adap= ter failed
5651 Financial Output ada= pter failed
5652 Output failure of printer or adapter
5653 The customization da= ta for thr printer missing
5654 Loop cable for the printer not connected
5655 Printer redirect -- error in the order of CONFIG.SYS file
5661 Financial Security adapter failed
5662 Data Encryption tried during normal operation without the Financial. Security adapter instal= led
5663 No "Master Key" is present in the Financial Security adapter
5690 4700PC banking featu= res not those expected.
5691 (PS/2) Device driver error.
62xs - IBM Store Loop Adapter. 's' is the slot number
6201 (PS/2) Replace (Store Loop) Adapter
621s - Multiple errors Replace (Store Loop) Adapter
622s - 8051 POR errors 80= 51 POR Error Check Status
623s - Latch test errors Latch Test Errors Check Status
624s - Shared buffer erro= rs. Shared Buffer Error Check Status
625s - CMOS test errors. = CMOS TEST Error Check Status
626s - Dump latch errors. Dump Latch Error Check Status
6270 (PS/2) Cable or Adap= ter Error
6280 (PS/2) Dump switch n= ot Operated in time
6290 (PS/2) NO Store loop adapter Present (Check Install List).
63xx 2nd Store Loop Adapt= er (see 62xs codes)
6421 Ethernet adapter is installed but no cable or terminator is attached. Put a terminator onto the Ethernet card's BNC connector
6907 System/36 PC expansi= on cable left attached to PC while running 36 Driver Card diagnostics
71xx Voice Communications Adapter
7101 - I/O Control Regist= er
7102 - Instruction or External Data Memory
7103 - PC to VCA Interrup= t
7104 - Internal Data Memo= ry
7105 - DMA
7106 - Internal Registers=
7107 - Interactive Shared Memory
7108 - VCA to PC interrup= t
7109 - DC Wrap
7111 - External Analog Wr= ap & Tone output
7112 - Mic to Spkr Wrap <= /li>
7114 - Telephone Attach T= est
74xx 8514/A Display Adapt= er
7401 - VGA logic
7402 - VGA test pattern <= /li>
7404 - VGA test pattern <= /li>
7406 - VGA test pattern <= /li>
7408 - VGA test pattern <= /li>
7412 - VGA test pattern <= /li>
7420 - Advanced function = test pattern (serialiser test)
7421 - ROM checksum Repla= ce the 8514/A Adapter
7422 - Register test Repl= ace the 8514/A Adapter
7423 - Update controls Replace the 8514/A Adapter
7424 - Functions test Rep= lace the 8514/A Adapter
7425 - Palette RAM test Replace the 8514/A Adapter
7426 - Comparators Replace the 8514/A Adapter
7427 - VRAM - palette addressing Replace the 8514/A Adapter
7428 - Interrupt test
7435 - 4/8 plane jumper on auxiliary storage card incorrect
7440 VRAM data error -- Module 31 defective
7441 VRAM data error -- Module 30 defective
7442 VRAM data error -- Module 29 defective
7443 VRAM data error -- Module 28 defective
7444 VRAM data error -- Module 22 defective
7445 VRAM data error -- Module 21 defective
7446 VRAM data error -- Module 18 defective
7447 VRAM data error -- Module 17 defective
7448 VRAM data error -- Module 32 defective
7449 VRAM data error -- Module 14 defective
7450 VRAM data error -- Module 13 defective
7451 VRAM data error -- Module 12 defective
7452 VRAM data error -- Module 06 defective
7453 VRAM data error -- Module 05 defective
7454 VRAM data error -- Module 02 defective
7455 VRAM data error -- Module 01 defective
7458 VRAM error, not data check -- Replace the 8514/A Adapter
7460 VRAM data error -- Module 16 defective
7461 VRAM data error -- Module 27 defective
7462 VRAM data error -- Module 26 defective
7463 VRAM data error -- Module 26 defective
7464 VRAM data error -- Module 24 defective
7465 VRAM data error -- Module 23 defective
7466 VRAM data error -- Module 20 defective
7467 VRAM data error -- Module 19 defective
7468 VRAM data error -- Module 15 defective
7469 VRAM data error -- Module 11 defective
7470 VRAM data error -- M= odule 10 defective
7471 VRAM data error -- Module 09 defective
7472 VRAM data error -- Module 08 defective
7473 VRAM data error -- Module 07 defective
7474 VRAM data error -- Module 04 defective
7475 VRAM data error -- Module 03 defective
7478 VRAM error, not data check -- Replace the 8514/A Adapter
7509 Display error
7510 XGA adapter or adapt= er memory error
76xx - 4216 Pageprinter <= /li>
7601 - Printer adapter ca= rd error
7602 - Printer adapter ca= rd error
7603 - Printer error
7604 - Printer cable erro= r
7801 (PS/2) Replace High Speed Adapter
7901 3117 Adapter Error Replace Adapter
7902 3117 Scanner lamp or device card problem
7903 3117 Scanner cable e= rror check or replace cable
8201 Info window NORMAL P= OWER ON
8202 Info window TIMER RE= SET (TIMEOUT) System controller board
8203 Info window 8031 CHIP System controller board
8204 Info window RAM Syst= em controller board
8205 Info window ROM CRC = ROM or System controller board
8206 Info window RAM CRC System controller board
8207 Info window NVRAM CRC Was display power switch off during an update? Data was restored -- may have system controller board problem
8208 Info window NVRAM BATTERY NVRAM battery or System controller board
8209 Info window NVRAM FAILURE System controller board
8210 Info window NVRAM DA= TA INVALID Replace system controller board if problem persists due to possible intermittent NVRAM
8211 Info window ANALOG-TO-DIGITAL System controller board
8212 Info window GRAPHIC = SYNC FAILURE Sync card or System controller board
8213 Info window TIME OF = DAY CLOCK Set time and Date. If problem persists replace System controller board, Sync card or Audio card
8214 Info window SPEECH L= OGIC FAILURE Audio card, System controller board or Power supply
8215 Info window INTERNAL= RS 232C WRAP System controller board
8216 Info window EXTERNAL= RS 232C WRAP Run test with the wrap plug on
8217 Info window HIGH RESOLUTION SYNCS. If the test screen was distorted: IBM EGA card or IBM EGA jumper card. If the test screen was readable: Sync card or System controller board
8218 Info window LOW FREQUENCY SYNCS. If the test screen was distorted: IBM EGA card or IBM= EGA jumper card. If the test screen was readable: Sync card or System controller board
8219 Info window EGA RGB SIGNALS TEST EGA, jumper, sync or system controller
8220 Info window RGB INSE= RT COMPARE Sync card
8221 Info window MISSING HI/LOW BEEPS Audio card or System controller board
8222 Info window RT CHANN= EL AUDIO Audio card or System controller board
8223 Info window LT CHANN= EL AUDIO Audio card or System controller board
8224 Info window NO SYNCS VIDEO '1 Sync, Decoder or System Controller
8225 Info window NO SYNCS VIDEO '2 Sync, Decoder or System Controller
8226 Info window 16/64 CO= LOR MODE Switching card or System Controller
8227 Info window LEFT/RIG= HT SHIFT Deflectn, System Controller or Swtchg
8228 Info window AUX MONI= TOR ON/OFF Decoder or System Controller
8229 Info window INTERLACE ON/OFF Sync or Deflection boards
8230 Info window VIDEO IN= PUT SELECT Decoder or System Controller
8231 Info window RGB ONLY MODE Sync card
8232 Info window COMPOSITE ONLY MODE Sync, System Contrllr, Swtchg, Dcodr
8233 Info window OVERLAY Switching, Deflection or Sync
8234 Info window RGB/VIDEO Sync card
8235 Info window SYSTEM T= IMER TEST System controller card
8236 Info window INTERNAL PROGRAM Verify system diskette and ROM levels for compatibility or swap System controller board
8237 Info window CANNOT CALIBRATE Syst contrlr, Touch scrn, Power supply
8238 Info window CONTROL PROGRAM Contact support - possible Syst ctrlr
8239 Info window CONTROL PROGRAM Contact support - possible Syst ctrlr
8240 Info window CPU NOT LISTENING IBM GPIB card or System controller
8241 Info window GPIB SEND/RECV COUNT Contact support
8242 Info window RS-232C = INTERFACE Run the wrap test with plug on display. Possible System controller boa= rd problem
8243 Info window TOUCH SC= REEN System controller board
8244 Info window FAILURE = OF VDP-1 Locate problem in VDP-1 cable
8245 Info window FAILURE = OF VDP-2 Locate problem in VDP-2 cable
8246 Info window A1/A2 DETECTION Sync card or System controller board
8247 Info window HIGH RESOLUTION SYNCS Sync card
8248 Info window TV FREQU= ENCY SYNCS Sync card
8249 Info window GPIB (BU= S) System controller board
8250 Info window CRC ERRO= RS DETECTED IEEE 488 cable, GPIB card or Syst ctrl
8251 Info window CRC ERRO= RS DETECTED IEEE 488 cable, GPIB card or Syst ctrl
8252 Info window GPIB TIME OUT GPIB card, Syst controller, IEEE 488 cable, Power supply or Videod= isc player problem
8253 Info window GPIB TIME OUT (Same as 8252)
8254 Info window GPIB SEQUENCE ERROR Contact support
8255 Info window INT PROG= RAM ERROR Contact support - possible Syst ctrlr
8256 Info window TIME OUT Syst controller, Sync card, IEEE 488 cable or IBM PC GPIB card
8257 Info window RETRIES = OF CRC ERRORS Syst ctrl, IEEE 488 cable or GPIB card
8258 Info window ERROR IN GPIB COMMS Syst ctrl, IEEE 488 cable or GPIB card
8259 Info window GPIB CONTROLLER ERROR GPIB card, IEEE 488 cable or Syst ctrl
8260 Info window INSERT CONTROL LOGIC Sync card or System controller board
8261 Info window WRONG RGB COLOR Video output board, Switching card, Sync card, System controller board or CRT and yoke assembly
8262 Info window PLAYER RESPONSE Verify videodisc on and has videodisc. Follow IBM Infowindow instructions to test videodisc player interface
8263 Info window ADDITION= AL EQUIPMENT If Audio problem, replace audio card. If dual frequency moni= tor problem, replace switching card. If color composite monitor problem, replace decoder card
8264 Info window RGB OUTP= UT SIGNALS Sync card
8265 Info window EGA CLOCK ERROR IBM EGA jumper card or IBM EGA card
8266 IBM EGA jumper inter= rupt error EGA switches, jumper card or adapter
8267 Info window EGA GRAP= HICS SYNC Sync cable, Jumper, Sync or EGA cards
8268 Sync present without cable IBM EGA card
8269 No audio videodisc 1= /L input Audio card
8270 No audio videodisc 2= /R input Audio card
8271 Info window IBM EGA = CARD Check out EGA card
8272 Info window EGA MEMO= RY FAILURE Replace IBM EGA card
8273 Info window EGA GRAP= HICS MEMORY Check out EGA memory modules
8274 Reserved Contact sup= port
8275 Reserved Contact sup= port
8276 Diskette cannot supp= ort See IBM Infowindow
8276 Display rom level compatibility levels
8277 Reserved Contact sup= port
8278 Info window HI RES DISPLAY Switching card, Sync ard or EGA
8279 Info window TIME OF = DAY CLOCK System controller board
8280 IBM PC DOS ERROR OCCURRED Follow directions on screen
84xx Speech Adapter error= s
8530 - IBM XMA (Expanded Memory Adapter). Determine if the XMA card appears in your Installed Devices list when running the diagnostics. If the list does not match = your configuration (either the list says the card is present, when it is no= t in fact present; or the list says the card is not present when it in fact= IS present), try re-running SETUP (menu option 4) and see if the error go= es away. If the card is present and the list shows it, verify that the am= ount of memory reported matches the amount of memory on the card. If it does not, then perhaps you have the XMA and/or system board memory jumpers = set incorrectly. Also make sure that you have no other memory adapters addressing the 256K-640K space.
8601 (PS/2) System board error or mouse error
8602 (PS/2) User indicated mouse error--Include DASDDRVR.SYS in your CONFIG.SYS. Load Reference Diskette and type A:INSTALL
8602 POST error may be a a bad mouse
8603 (PS/2) System board = or mouse error
8604 (PS/2) System board = or mouse error
8611 (Thinkpad) Keyboard pointing stick error
8612 (Thinkpad) Keyboard control card error
8613 (Thinkpad) System bo= ard error
89xx IBM Music card
91xx 3363 optical drive error: Reset cables and adapters. Attempt F1 after error code and run Advanced Diagnostics.
9101 Optical disk - Drive= '1 failed - Reseat Cables and Adapter
9102 Optical disk - Drive= '1 failed - Reinsert Cartridge, Reseat Adapter
9103 Optical disk - Drive= '1 failed - Reseat Cables and Adapter
9104 Optical disk - Drive= '2 failed - Reseat Cables and Adapter
9105 Optical disk - Drive= '2 failed - Reinsert cartridge,Reseat cables+Adaptr
9106 Optical disk - Drive= '2 failed - Reseat cables and Adapter
9107 Optical disk - Adapt= er hung on BUSY - Reseat Cables and Adapter
9110 Optical disk - Data = not recorded - Check Adapter, Drive, Cable
9111 Optical disk - Data = not readable - Check Adapter, Drive, Cable
9112 Optical disk - Sector demarked - Check Adapter, Drive, Cable
9113 Optical disk - Controller Error - Check Adapter, Drive, Cable - Check switch settings= on Adapter DS302 (check setting 8088 vs 80286)
9114 Optical disk - Sector Read/Write Error - Check Drive, Adapter, or Cable
9115 Optical disk - Scram= ble Buffer Error - Check Drive, Adapter and Cable
9116 Optical disk - Data Buffer Error - Check Drive, Adapter and Cable
9117 Optical disk - Drive RAM/ROM Error - Check Drive, Adapter and Cable
9118 Optical disk - Inval= id Command - Check Drive, Adapter, Cable
9119 Optical disk - Track Jump Error - Check Drive, Adapter, Cable
9120 Optical disk - Laser Error - Check Drive, Adapter, or Cable
9121 Optical disk - Focus Error - Check Cartridge, Drive, Adapter, or Cable
9122 Optical disk - Motor Sync Error - Cartridge upside down - Check Drive, Adapter, Cable
9123 Optical disk - Write Fault - Check Drive, Adapter, or Cable
9124 Optical disk - Gener= al Drive Error - Check Drive, Adapter and Cable
9125 Optical disk - Sense Command Failed - Check Drive, Adapter and Cable
9126 Optical disk - Inval= id Command - Check Drive, Adapter, Cable
9127 Optical disk - Sense Command Failed - Check Drive, Adapter and Cable
9128 Optical disk - Disk = Not Initialized - Check Drive, Adapter and Cable
9129 Optical disk - Disk = ID Did Not Match - Check Drive, Adapter and Cable
9130 Optical disk - Read-= Only Disk Installed - Chk Disk, Drive, Adaptr, Cable
9131 Optical disk - No Di= sk Present - Check Disk, Drive, Adapter, Cable
9132 Optical disk - Illeg= al Disk Detected - Check Disk, Adaptr, Drive, Cable
9133 Optical disk - No Di= sk Change Detected - Check Drive, Adapter, Cable
9134 Optical disk - Read-= Only Disk Detected - Check Drive, Adapter, Cable
9135 Optical disk - Illeg= al Disk Detected - Check Drive, Adapter, Cable
9136 Optical disk - Sense Command Failed - Check Adapter, Drive, Cable
9138 Optical disk - No Di= sk Change Detected - Retry test again - Check Drive, Adapter, Cable
9141 Optical disk - No Di= sk Change Detected - Retry tests (See 9138)
9144 Optical disk - WRITE-PROTECT Window Not Opened - Retry tests (See 9138)
9145 Optical disk - No Di= sk Change Detected - Retry tests (See 9138)
9146 Optical disk - WRITE-PROTECT Window Not Closed - Retry tests (See 9138)
9148 Optical disk - Adapt= er Card - Check Adapter, Drive, or Cable
9150 Optical disk - Seek Command Failed - Check Drive, Adapter, Cable
9151 Optical disk - Not At Track Zero - Check Drive, Adapter, Cable
9152 Optical disk - Track Address Error - Check Drive, Adapter, Cable
9153 Optical disk - Not At Track 17099 - Check Drive, Adapter, Cable
9154 Optical disk - Track Address Error - Check Drive, Adapter, Cable
9155 Optical disk - Track Address 17K Not Found - Check Drive, Adapter, Cable
9156 Optical disk - Seek = Time Too Long - Check Drive, Adapter, Cable
9157 Optical disk - Sense Command Failed - Check Drive, Adapter, Cable
9158 Optical disk - No Da= ta Read Error Found - Check Drive, Adapter, Cable
9159 Optical disk - No Nu= ll Sector Found - Check Drive, Adapter, Cable
9160 Optical disk - Sense Command Failed - Check Drive, Adapter, Cable
9161 Optical disk - Write Command Failed - Check Drive, Adapter, Cable
9162 Optical disk - Data = Compare Error - Check Drive, Adapter, Cable
9163 Optical disk - Read Verify Error - Check Drive, Adapter, Cable
9164 Optical disk - Demark Verify Failed - Check Drive, Adapter, Cable
9165 Optical disk - Demark Bit Not Set - Check Drive, Adapter, Cable
9166 Optical disk - Seek = 1/3 Timing Error - Check Drive, Adapter, Cable
9167 Optical disk - Seek = 2/3 Timing Error - Check Drive, Adapter, Cable
9168 Optical disk - Seek = 3/3 Timing Error - Check Drive, Adapter, Cable
9170 Optical disk - Seek Error Set - Check Drive, Adapter, Cable
9171 Optical disk - Controller RAM/ROM Error - Check Drive, Adapter, Cable
9172 Optical disk - Demark Function Error - Check Drive, Adapter, Cable
9173 Optical disk - Detec= ted Error Set - Check Drive, Adapter, Cable
9174 Optical disk - Modulator/Demodulator Error - Check Drive, Adapter, Cable
9175 Optical disk - Inval= id Command - Check Adapter, Drive, Cable
9176 Optical disk - Illeg= al Disk Error - Check Adapter, Drive, Cable
9177 Optical disk - Both drives set to same address or wrong address
9178 Optical disk - ID Mismatch - Check Drive, Adapter, or Cable
9179 Optical disk - Sector Not Found - Check Drive, Adapter, Cable
9181 Optical disk - Sense Command Failed - Check Drive, Adapter, Cable
9182 Optical disk - Read Command Error - Check Drive, Adapter, Cable
9185 Optical disk - Diagnostic Track Error - Check Drive, Adapter, Cable
9186 Optical disk - Diagnostic Demark Error - Check Drive, Adapter, Cable
9187 Optical disk - No De= mark Bit Set - Check Drive, Adapter, Cable
9198 Optical disk - Inval= id Command - Re-IPL CPU with ON/OFF switch
96xxxT SCSI Adapter w/cac= he, SCSI device or system board
For T=3D A 60MB, B 80MB, C 120MB, D 160MB, E 320MB, F 400MB, G 40MB, H= 1GB, I 100MB, J 200MB, U Undetermined
10001 (PS/2) Can not dete= ct presence of Multi Protocol Communications Adapter
10002 (PS/2) Card selected feedback error
10003 (PS/2) Port 102H register test failure
10004 (PS/2) Port 103H register test failure
10006 (PS/2) Serial option can not be put to sleep
10007 (PS/2) Cable error =
10008 (PS/2) Async IRQ3 e= rror
10009 (PS/2) Async IRQ4 e= rror
10010 (PS/2) 16550 async = chip register failure
10011 (PS/2) Internal wrap test of 16550 modem control line failure
10012 (PS/2) External wrap test of 16550 modem control line failure
10013 (PS/2) 16550 transm= it error
10014 (PS/2) 16550 receive error
10015 (PS/2) 16550 receive error data not equal transmit data
10016 (PS/2) 16550 interr= upt function error
10017 (PS/2) 16550 fails = baud rate test
10018 (PS/2) 16550 interr= upt driven receive external data wrap test failure
10019 (PS/2) 16550 FIFO <= /li>
10026 (PS/2) 8255 Port A error
10027 (PS/2) 8255 Port B error
10028 (PS/2) 8255 Port C error
10029 (PS/2) 8254 timer 0 error
10030 (PS/2) 8254 timer 1 error
10031 (PS/2) 8254 timer 2 error
10032 (PS/2) Bisync DSR response to DTR error
10033 (PS/2) Bisync CTS response to RTS error
10034 (PS/2) 8251 hardware reset test failed
10035 (PS/2) 8251 function error: internal software reset test failed
10035 (PS/2) 8251 error r= eset command failed or 8251 can not detect overrun err
10036 (PS/2) 8251 status error: 8251 Tx ready error
10037 (PS/2) 8251 Rx ready error or Bisync timer interrupt error
10038 (PS/2) Bisync trans= mit interrupt error
10039 (PS/2) Bisync recei= ve interrupt error
10040 (PS/2) Stray IRQ3 e= rror
10041 (PS/2) Stray IRQ4 e= rror
10042 (PS/2) Bisync exter= nal wrap error
10044 (PS/2) Bisync data = wrap error
10045 (PS/2) Bisync line status/condition error
10046 (PS/2) Bisync time = out error during data wrap test
10050 (PS/2) 8273 command acceptance or results ready time out error
10051 (PS/2) 8273 Port A error
10052 (PS/2) 8273 Port B error
10053 (PS/2) SDLC modem status change logic error
10054 (PS/2) SDLC timer interrupt (IRQ4) error
10055 (PS/2) SDLC modem s= tatus change interrupt (IRQ4) error
10056 (PS/2) SDLC external wrap error
10057 (PS/2) SDLC interru= pt results error
10058 (PS/2) SDLC data wr= ap error
10059 (PS/2) SDLC transmit interrupt error
10060 (PS/2) SDLC receive interrupt error
10061 (PS/2) DMA channel 1 error (transmit)
10062 (PS/2) DMA channel 1 error (receive)
10063 (PS/2) 8273 status detect failure
10064 (PS/2) 8273 error detect failure
10101 (PS/2) Can not dete= ct presence of modem
10102 (PS/2) Card selected feedback error
10103 (PS/2) Port 102H register test failure
10106 (PS/2) Serial option can not be put to sleep
10108 (PS/2) Async IRQ3 e= rror
10109 (PS/2) Async IRQ4 e= rror
10110 (PS/2) 16450 async = chip register failure
10111 (PS/2) Internal wrap test of 16450 modem control line failure
10113 (PS/2) 16450 transm= it error
10114 (PS/2) 16450 receive error
10115 (PS/2) 16450 receive error data not equal transmit data
10116 (PS/2) 16450 interr= upt function error
10117 (PS/2) 16450 fails = baud rate test
10118 (PS/2) 16450 interr= upt driven receive external data wrap test failure
10125 (PS/2) Modem reset result code error
10126 (PS/2) Modem general result code error
10127 (PS/2) Modem S registers write/read error
10128 (PS/2) Modem turn e= cho on/off error
10129 (PS/2) Modem enable= /disable result codes error
10130 (PS/2) Modem enable number/word result codes error
10133 (PS/2) Connect resu= lts for 300 baud not received
10134 (PS/2) Connect resu= lts for 1200 baud not received
10135 (PS/2) Modem fails local analog loop back test at 300 baud
10136 (PS/2) Modem fails local analog loop back test at 1200 baud
10137 (PS/2) Modem does n= ot respond to escape/reset sequence
10138 (PS/2) S reg 13 does not reflect correct parity or number of data bits
10139 (PS/2) S reg 15 does not reflect correct bit rate
102XX (PS/2) 4250 Print Adapter failure
10400 (PS/2) Unknown. FRU drive, then controller, then system board
10403 (PS/2) Defective 12= 0M byte hard-disk drive.
10436 (Thinkpad, N51) Sys= tem board, fixed disk or cable error
10440 - 10447 (PS/2) 8550= -021 60 Meg ESDI Adapter Error.
10450 (PS/2) Replace drive (read write test failed)
10451 (PS/2) Replace drive (read verify test failed)
10452 (PS/2) Replace drive (seek test failed)
10453 (PS/2) Replace drive (wrong device type indicated)
10454 (PS/2) Controller (controller test failed sector buffer test)
10455 (PS/2) Controller failure
10456 (PS/2) Controller (= diag command failure) -- Replace drive
10457 (PS/2) Repl. drive (integrated controller test failure)
10458 (PS/2) Repl. drive (integrated controller test failure)
10458 (PS/2) If 8570-121 = or 8570-A21 see ECA020
10459 (PS/2) Replace drive (diag command failure)
10460 (PS/2) Unknown. FRU drive, then controller, then system board
10461 (PS/2) Drive format error
10462 (PS/2) Controller (= head select error)
10463 (PS/2) Drive (read/write sector error)
10464 (PS/2) Drive (prima= ry map unreadable)
10465 (PS/2) Controller (= ECC 8 bit error)
10466 (PS/2) Controller (= ECC 9 bit error)
10467 (PS/2) Drive (soft = seek error)
10468 (PS/2) Drive (hard = seek error)
10469 (PS/2) Drive (soft = seek error count exceeded)
10470 (PS/2) Controller (attachment diagnostic error)
10471 (PS/2) Controller (= wrap mode interface error)
10472 (PS/2) Controller (= wrap mode drive select error)
10473 (PS/2) Unknown. FRU drive, then controller, then system board. The controller has found a sector on the disk with bad ECC. This is very easy to cause. It is usu= ally not a hardware failure. The only way to fix the failure besides a refo= rmat is to find the sector and rewrite it. There is no need for a low level format; A DOS format should fix it.
10474 (PS/2) Unknown. FRU drive, then controller, then system board
10475 (PS/2) Unknown. FRU drive, then controller, then system board
10476 (PS/2) Unknown. FRU drive, then controller, then system board
10477 (PS/2) Unknown. FRU drive, then controller, then system board
10478 (PS/2) Unknown. FRU drive, then controller, then system board
10479 (PS/2) Unknown. FRU drive, then controller, then system board
10480 (PS/2) Drive 0 seek failure or Controller (com/data - attention bad) Faulty C: drive, a se= ek failure. Replace the drive.
10481 (PS/2) Drive 1 seek failure or Controller (xfr req - ready bad)
10482 (PS/2) Controller t= est failure or Controller (drv sel 1 - xfr ack bad)
10483 (PS/2) Controller r= eset fail or Controller (drv sel 0 - config/stat bad). Fixed by pulling/re-pluging the T-card between system board and hard disk. Also reported fixed by replacing suspect drive
10484 (PS/2) Controller (= head sel 3 - selected bad)
10485 (PS/2) Controller (= head sel 2 - selected bad) << See 10483
10486 (PS/2) Controller (= head sel 1 - selected bad)
10487 (PS/2) Controller (= head sel 0 - selected bad)
10488 (PS/2) Controller (= rg - cmd complete 2)
10489 (PS/2) Controller (= wg - cmd complete 1)
10490 (PS/2) Drive 0 read failure or Controller (drive connected no test done)
10491 (PS/2) Drive 1 read failure
10499 (PS/2) Controller failure
106xx Ethernet Adapter
107xx 1.2MB Internal/Exte= rnal Adapter
10701 (PS/2) Post Error Replace Adapter
10759 (PS/2) Write-protect error
109xx Action Media Adapte= r
10917 Audio wrap or speak= er problem
10919 Video cable bad or = not connected
1094x Capture option bad =

! The following text provides a summary of the error codes which are
! used by the ActionMedia II diagnostics.
!
! The error codes discussed applies to both MCA and ISA versions of the
! diagnostic.
!
! Diagnostics Error Code Format
!
! The general error code format is shown below:
!
! 0 1 0 9 m m s x
! \_______________/ \___/ ! !
! ! ! !* !
! ActionMedia II Main Error Slot Sub
! Adapter/A device id Code Number Error
! Code
!
! * MCA only (Set to zero for ISA diagnostics)
!
! Error Code Reference
!
! Test Error Codes Description of
! Main Sub Failing Test
! ------------------------------------------------------------
! CS2 control 44 0 Echo 2aah using EchoBack register
! register 1 Echo 155h using EchoBack register
! 2 Echo 00h using EchoBack register
! ------------------------------------------------------------
! CS2 6805 43 0 Check Memory test status
! 1 Check Arithmetic test status
! 2 Check Checksum test status
! ------------------------------------------------------------
! CS2 VICTOR 41 0 Horizontal Start register w/r
! 1 Horizontal Stop Y register w/r
! 2 Horizontal Offset Y register w/r
! 3 Horizontal Offset VU register w/r
! 4 Horizontal Total register w/r
! 5 Vertical Start register w/r
! 6 Vertical Stop register w/r
! 7 Vertical Scale register w/r
! 8 YVU Control register w/r
! 9 Horizontal Stop VU register w/r
! ------------------------------------------------------------
! CS2 CHROMA 42 0 Blue Gain Offset register w/r
! 1 Blue DC Offset register w/r
! 2 Red Gain Offset register w/r
! 3 Red DC Offset register w/r
! 4 Contrast register w/r
! 5 Hue register w/r
! 6 Brilliance register w/r
! 7 Saturation Main register w/r
! 8 Saturation Balance register w/r
! 9 Direct Access register w/r
! ------------------------------------------------------------
! CS2 CHROMA 45 0 CHROMA communication link test
! link
! ------------------------------------------------------------
! DS2 PAR 05 0 bit walk test for PAR0
! 1 bit walk test for PAR1
! 2 bit walk test for PAR2
! 3 bit walk test for PAR3
! 4 write/read ffffh to/from PAR0-3
! 5 write/read aaaah to/from PAR0-3
! 6 write/read 5555h to/from PAR0-3
! 7 write/read 33cch to/from PAR0-3
! 8 write/read cc33h to/from PAR0-3
! 9 write/read 0f0fh to/from PAR0-3
! ------------------------------------------------------------
! DS2 FIFO 06 0 32 Bit FIFO w/r of 55aah and
! aa55h at VRAM addr =3D 000000h
! 1 16 Bit FIFO read of above data
! 2 Check above data via PAR0-3
! 3 16 bit FIFO write of faf5h & 5fafh to VRAM addr 00h & check via PAR3
! 4 32 bit FIFO write/read of cccch & 3333h to/from VRAM addr =3D 0ffff= ch
! 5 16 bit FIFO read of above data
! 6 Check above data via PAR0-3
! 7 16 bit FIFO write of 9696h & 6969h to VRAM addr ffffch, check via <= br> ! PAR3. Write 0a5c3h and 03c5ah to the PB via the 16 bit Write FIFO
! 8 Read 0a5c3h and 03c5ah from the PB via the 16-bit read FIFO
! 9 Read 0a5c3h and 03c5ah from the PB via each PAR (0-3) in turn
! ------------------------------------------------------------
! DS2 QAR 08 0 Write 0f0fh data to VRAM addr 10h.
! Write/Read 0aa55h to/from DVI
! Device 7 via addr =3D 10h using the QAR and read it back
! 1 Check that original 0f0fh data at VRAM addr =3D 10h is still present ! 2 Write/Read 055aah to/from DVI Device 7 via addr =3D 10h using the
! QAR and read it back
! ------------------------------------------------------------
! DS2 Palette 09 0 Write (red=3D2ah,green=3D15h,blue=3D2ah)
! to colour 0 of host (and DS2) palette and read back from host
! 1 Read back the colour 0 data via the DS2 palette
! 2 Write 15h,2ah,15h to colour 0 of the DS2 palette and read it back
! 3 Write 30h,0fh,30h to colour 0 of the DS2 palette and read it back
! ------------------------------------------------------------
! DS2 VRAM 11-14 0-7 Failing VRAM module within the
! ! MB block in error
! (10+MB block in error)
! e.g. 11 for base 1MB
! ------------------------------------------------------------
! DS2 DSP 17 0 Load code to return a value
! from the DCP
! 1 Run code and check value
! 2 Load/execute code to check that
! messages can be sent to/from DSP
! 3 Load the loop back test code
! 4 Run the loop back test code
! 5 Load the Playback and Capture
! interupts test
! 6 Execute test and check for
! correct response to test
! 7 Load audio wrap test code
! 8 Wrap a 0V audio signal
! 9 Wrap a sine wave audio signal
! ------------------------------------------------------------
! DS2 SCSI 10 0 Load all SCSI registers with 00h
! Check that SCSI register 7 =3D 0
! 1 Read 0's from/ write f's to the other six SCSI registers
! 2 Read f's from/ write a's to the other six SCSI registers
! 3 Read f's from/ write a's to SCSI register 7
! ------------------------------------------------------------
! Video Wrap 30 0 Check that '% Y in bucket' value
! Circuitry is within the permitted tolerance
! 1 Check that '% U in bucket' value is within the permitted tolerance
! 2 Check that '% V in bucket' value is within the permitted tolerance
! 3 Check 'Y mean offset' value is within the permitted tolerance
! 4 Check 'U mean offset' value is within the permitted tolerance
! 5 Check 'V mean offset' value is within the permitted tolerance
! ------------------------------------------------------------

112xx SCSI adapter or any SCSI device
11944 3119 Adapter Error Replace Adapter
11945 3119 Possible Power Supply or Lamp Problem.
11950 - 11954 3119 Lamp or Optics Problem.
11957 - 11958 3119 Possib= le Optics problem or 3119 Adapter Problem.
121xx 3/12/24 Internal Mo= dem
12101 ISDN Adapter error =
12110 Defective ISDN adap= ter
12120 Defective ISDN adap= ter or wrap connector
129xx Processor card erro= rs: RE-SEAT THE PROCESSOR CARD and second level cache
12901 Processor Error
12902 Cache Error: Re-seat connection between the processor board (daughter card) and main planar=
12903 Coprocessor Error <= /li>
12904 Second level cache failure. Problem may be require replacing the cache card attached to t= he processor card.
01290400 L2 cache parity
12905 (PS/2) Second level cache warning
12906 (PS/2) Second level cache warning
12907 (PS/2) Second level cache fatal error
12908 (PS/2) Second level cache POST error
01291200 WATCHDOG TIMEOUT
12913 DMA Error
01291300 DMA BUS TIMEOUT
01291400 DMA SCB ERROR
01291500 Processor bus parity error
01291600 System bus parity error
012917xx Processor board cache error -- if a 20Mhz board is installed = and the processor is a 487SX, verify that the jumper is in positions 1 and= 2. If not processor board cache (256K), replace processor board or system= brd
01291800 Invalid configuration error
01291900 Voltage regulator problem; too hi/lo
0129300 Model 90/95 only, jumper J4 on the wrong pins
012940xx Processor board
012944xx A hardware default interrupt occurred
012950xx Processor board
0129x3xx Busmaster arbitration error. If more than one installed, remo= ve busmasters one at a time to isolate the failure
130xx ThinkPad Indicator Assembly or system board or any device
137xx ThinkPad, N51, or M= odel 90/95 serial adapter (system board)
141xx Real Time Interface Coprocessor Portmaster/A
143xx Japanese Display Adapter
14710 Video memory, Model 90/95 processor or system board, or Plasma display
14711 Video memory, Model 90/95 processor or system board, or Plasma display
148xx System board video memory, P75 display card
14901 Try FRU Plasma Disp= lay Adapter then System board, Plasma display
14902 Try FRU Plasma Disp= lay Adapter then System board, Plasma display
14922 Try FRU Plasma Disp= lay then Plasma display adapter, System brd
14932 Try FRU External Display then Plasma display adapter
14952 P75 Plasma display assembly
15201 XGA adapter card -- card found problems when running the VGA tests against itself.
15202 XGA adapter card -- card found problems testing the advanced function of XGA -- likely to = be memory past the first 256K or the Sprite
15203 XGA adapter card -- card can generate this error from the final set of tests
161xx Fax Concentrator Adapter
16451 (PS/2) Not enough memory to operate the tape drive
16452 (PS/2) Cartridge presence error
16453 (PS/2) Servo electronics/mechanism failed
16454 (PS/2) The cartridge was not formatted, or read chain failed
16455 (PS/2) The EOT test failed
16456 (PS/2) The BOT test failed
16457 (PS/2) Track follow= ing error -- servo electronics/mechanism failed
16458 (PS/2) Internal software error
16459 (PS/2) Floppy disk controller failure
16460 (PS/2) Internal software error
16461 (PS/2) Unrecoverable read error -- drive failure
16462 (PS/2) Internal software error
16463 (PS/2) User changed= the cartridge
16464 (PS/2) DMA controll= er failure
16465 (PS/2) General drive failure
16466 (PS/2) No internal = tape drives were found
16467 (PS/2) Write protect switch failed
16468 (PS/2) Unrecoverable write error -- drive failure
16469 (PS/2) Defective cartridge
16520 (PS/2) 6157 Tape Dr= ive Error
16540 (PS/2) 6157 Tape Attachment -- Adapter or Drive Error FRU Unknown. Use latest level Reference Diskette. When servicing an 8570 Model A21 (25mhz), use 6157 option diskette, version 1.02 (or higher). The programs on the option diskette must be merged onto the System Reference Diskette.
166xx Primary Token-Ring Network PC Adapter. 16600 Indicates Good Primary Adapter. Other codes indicate failure
167xx Alternate Token-Ring Network PC Adapter. 16700 Indicates Good Alternate Adapter. Other codes indicate failure
180xx or 1801xx (PS/2) Wi= zard adapter coprocessor busmaster card w/Intel i860
18001-18029 Indicates problems with the PS/2 Wizard Adapter
18031-18039 Indicates problems with the memory expansion board
18001 - Interrupt control= ler failure
18002 - Incorrect timer c= ount
18003 - Timer interrupt failure
18004 - Sync check interr= upt failure
18005 - Parity check interrupt failure
18006 - Access error interrupt failure
18012 - Bad checksum
18013 - MicroChannel interface error -- CLEAN card contacts
18021 - Memory error or parity error - Wizard (card) memory
18022 - Address line erro= r - Wizard (card) memory
18023 - Dram controller failure
18029 - Byte enable error= - Wizard (card) memory
18031 - Memory error or parity error - expansion (card) memory
18032 - Address line erro= r - expansion (card) memory
18039 - Byte enable error= - expansion (card) memory
1801xx PS/2 Wizard Adapter hardware error detected by software
180101-180129 Indicate problems with the PS/2 Wizard Adapter
180131-180139 Indicate problems with the memory expansion board. Interpret 1801xx errors using 180xx codes above
180164 - Memory size determined smaller than configured memory
180166 - Memory size determined larger than configured memory
18431 - Memory error dete= cted on 80386 Enhanced Memory Option card
18441 - Unsupported SIMM(= s) detected
18451 - Change in SIMM configuration
185xx DBCS Japanese Displ= ay Adapter/A
194XX 2-8MB 80286 Memory Expansion Adapter

20000 Image Adapter/A err= or
PS/2 Model 80, OS/2 1.3, 2 monitors (Image Adapter/A and VGA).
Running a PM application on the Image Adapter.
Screen suddenly goes blank except for following 2 lines in upper left corner

111
????

It indicates that one of your adapter cards h= as pulled the -CHCK line, NMI indicating that it has had an error of some sort. (This line goes to the interrupt on the processor, which puts up this crypt= ic message.) It is not easy to determine which card is at fault, or why.

20xyz Image Adapter/A err= or codes
All Image Adapter/A error codes are of a 20xyz format. The x variable = is defined as follows:
200yz; x =3D 0 - Original Image adapter card error code
201yz; x =3D 1 - Original Image adapter card plus daughter card error = code
204yz; x =3D 4 - Later Image adapter card error code
205yz; x =3D 5 - Later Image adapter card plus daughter card error cod= e

The yz variable is defined as follows :-

Mother Board Errors

20001 20101 20401 20501; yz =3D 01 - PROM che= ck sum test error
20002 20102 20402 20502; yz =3D 02 - Register test error
20003 20103 20403 20503; yz =3D 03 - Instruction RAM test error
20004 20104 20404 20504; yz =3D 04 - Local RAM test error (ie VRAM or DRAM problem). Check installation of memory chips or run diagnostics to locate failing chip.
20005 20105 20405 20505; yz =3D 05 - Pixel interface test error
20006 20106 20406 20506; yz =3D 06 - CRTC test error
20007 20107 20407 20507; yz =3D 07 - Palette test error
20008 20108 20408 20508; yz =3D 08 - DAC test error. With 6091, check that IA/output cable is not plugged into the 6091 outputs.
20010 20110 20410 20510; yz =3D 10 - Interrupt test error
20098 20198 20498 20598; yz =3D 98 - Bus mastership test error
20099 20199 20499 20599; yz =3D 99 - Slot test error

Option Card Errors

20111 20511; yz =3D 11 - Scanner wrap test er= ror
20112 20512; yz =3D 12 - Scanner serial to parallel shift test error
20113 20513; yz =3D 13 - Scanner line synchronisation counter test error 20114 20514; yz =3D 14 - Printer wrap test error
20115 20515; yz =3D 15 - Printer parallel to serial shift test error
20116 20516; yz =3D 16 - SCC Tx/Rx loop back test error
20117 20517; yz =3D 17 - SCC register test error
20118 20518; yz =3D 18 - External conditions and external interrupt test er= ror
20119 20519; yz =3D 19 - Processor failed to stop

20008 Image Adapter failu= re -- Accompanied by Long-Short-Short
Advanced Diagnostics error was 02000860
Check that outputs of the IA card are not hooked into the OUTPUTS of t= he 6091 POST and Image Adapter diagnostics are misleading DO NOT attempt = to F1 past the POST error into OS/2. It will actually "work" but will rewrite your OS/2 .INI files for low-resolution operation.

10 - Interrupt test error
98 - Bus mastership test error
99 - Slot test error

Option Card Errors

11 - Scanner wrap test error
12 - Scanner serial to parallel shift test error
13 - Scanner line synchronization counter test error
14 - Printer wrap test error
15 - Printer parallel to serial shift test error
16 - SCC Tx/Rx loop back test error
17 - SCC register test error
18 - External conditions and external interrupt test error
19 - Processor failed to stop

208xx Any SCSI device
242xx ISDN/2 Adapter
243xx XGA-2 Display Adapt= er
258xx System Board video failure

SCSI Error codes from appendix B of the SCSI Architecture and Implementa= tion manual, document number GG24-3507

Format: 0DDDPLSC QEET

0 Reserved (always a zero)
DDD SCSI Device Type
P SCSI Physical Unit Number
L SCSI Logical Unit Number
S MicroChannel Slot Number
C SCSI Device Size Code
Q Error Code Qualifier
EE Error Code
T Test State

Device types (DDD)

096 32-bit SCSI Adapter (with cache)
112 16-bit SCSI Adapter (without cache)
208 Unknown SCSI device type
209 Direct access - removable media and/or other than 512 byte blocks
210 Direct access - non-removable media, 512 byte blocks
211 Sequential access (tape drive)
212 Printer
213 Processor
214 Write-once Read-multiple (WORM)
215 Read only (CD ROM)
216 Scanner
217 Optical memory
218 Changer
219 Communications

Size Codes (C)

A 60MB
B 80MB
C 120MB
D 160MB
E 320MB
F 400MB
G 40MB
H 1GB
I 100MB
J 200MB
U Undetermined Size

Here is an example by decoding the SCSI message 0210608C 601I:

0210608C 601I
! ! !   ! !! ! !    +--> I: During the De= vice Assignment Sequence
! ! !   ! !! ! !
! ! !   ! !! ! +----> 601: SCSI reset occured / SCSI interface fault
! ! !   ! !! !
! ! !   ! !! +-------> C: Capacity of 120 MB
! ! !   ! !+-------> 8: Microchannel Slot 8
! ! !   ! +--------> 0: SCSI LUN 0 (boot drive)
! ! !   +---------> 6: SCSI PUN 6 (boot drive)
! +------------> 210: SCSI Hardfile
+--------------> 0: Always a zero

Generic Errors (S=3D0)

DDD0100 0000 No setup data available, or checksum did not verify
DDD0200 0000 No fixed disk at PUN 6, LUN 0
DDD0300 0000 No space available in extended BIOS area for SCSI data table <= br> DDD0400 0000 ROM modules not found on adapter
DDD0500 0000 ROM checksum error on 2nd 16k portion of 32k ROM

Error Codes with Q=3D0

0096---- 001 80188 ROM test failure
0096---- 002 Local RAM test failure
0096---- 003 External terminator missing or fuse bad
0096---- 004 80188 internal peripheral test failure
0096---- 005 Buffer control test failure
0096---- 006 Buffer RAM test failure
0096---- 007 System interface control test failure
0096---- 008 SCSI interface test failure
0112---- 001 8032 ROM test failure
0112---- 002 Local RAM test failure
0112---- 003 Local RAM address test failure
0112---- 004 8032 internal peripheral test failure
0112---- 005 Buffer control test failure
0112---- 006 Undefined error condition
0112---- 007 System interface control test failure
0112---- 008 SCSI interface test failure

Error Codes with Q=3D1

---------107 Adapter hardware failed
---------10C Command failed
---------10E Command error (invalid command or parameter)
---------10F Sequencing error
---------180 Timeout
---------181 Adapter busy error
---------182 Unexpected interrupt presented by adapter
---------183 Adapter register test failed
---------184 Adapter Reset
---------185 Adapter buffer test failure (cached only)
---------186 Adapter reset count expired
---------187 Adapter registers not cleared on reset
---------188 Card ID in adapter did not match ID in POS registers
---------190 Expected device did not respond
---------19X DMA arbitration level conflict

Error Codes with Q=3D2

---------220 Adapter hardware error
---------221 Global timeout on adapter
---------222 Adapter DMA error
---------223 Adapter buffer defective
---------224 Command aborted by adapter

Error Codes with Q=3D3

---------301 Invalid parameter in SCB
---------303 Command not supported
---------304 Command aborted by system
---------305 Command rejected (buffer not disabled)
---------306 Command rejected (adapter diagnostic failure)
---------307 Format rejected
---------308 Assign rejected (command in progress
---------309 Assign rejected (device already assigned)
---------30A Command rejected (device not assigned)
---------30B Command rejected (maximum LBA exceeded)
---------30C Command rejected (16 bit card slot address exceeded)
---------313 Invalid device for command
---------3FF Status not returned by adapter

Error Codes with Q=3D4

---------401 Recovered error
---------402 Device not ready
---------403 Device medium error
---------404 Device hardware error
---------405 Illegal request for device
---------406 Device unit attention would not clear
---------407 Device data protect error
---------409 Device vendor unique error
---------40A Device copy aborted
---------40B Device command aborted
---------40C Device search data command satisfied
---------40D Device volume overflow (residual data in buffer)
---------40E Device miscompare, source data did not match medium data

Error Codes with Q=3D5

---------501 No index or sector
---------502 Seek incomplete
---------503 Write fault
---------504 Drive not ready
---------505 Drive not selected
---------506 No track zero found
---------507 Multiple drives selected
---------508 Logical unit communications failure
---------509 Head positioning error (track following error)
---------510 CRC or ECC error in ID field
---------511 Unrecoverable read error
---------512 No address mark (ID field)
---------513 No address mark (data field)
---------514 Record not found
---------515 Seek error
---------516 Data Synchronization error
---------517 Recoverable read (without ECC) error
---------518 ECC recovered read error
---------519 Defect list error
---------51A Parameter overrun
---------51B Synchronous transfer error
---------51C Primary defect list not found
---------51D Compare Error
---------520 Invalid command
---------521 Illegal logical block address (LBA)
---------522 Illegal function for device type
---------524 Illegal command block field
---------525 Illegal LUN
---------526 Illegal field in parameter list
---------528 Media changed
---------529 Power on or bus device reset occurred (not an error)
---------52A Mode select parameters changed (not an error)
---------531 Medium format corrupted
---------532 Defect spare location unavailable
---------540 Device RAM failure
---------541 Data path diagnostic failure
---------542 Power on diagnostic failure
---------543 Message rejected
---------544 Internal controller error
---------545 Device was unable to re-connect
---------547 Interface parity error
---------548 Initiator detected error
---------549 Illegal command or command out of sequence error
---------5F0 Format in progress (not an error)
---------5F1 Spin up in progress

Error Codes with Q=3D6

---------601 SCSI bus reset occurred
---------602 SCSI interface fault
---------610 Selection timeout error
---------611 Unexpected bus free
---------612 Mandatory SCSI message rejected
---------613 Invalid SCSI phase sequence
---------620 Short length record

Error Codes with Q=3D7

---------702 Device not ready - removable media
---------704 Device not ready - fixed media
---------728 Media changed error would not clear
---------731 Medium format corrupted
---------7F0 Format in progress
---------7F1 Spinup in progress

Test state in which failure occurred (T)

0 Not applicable for error code
A Adapter Initialization
B Adapter reset
C Adapter register test
D Adapter buffer test phase 1 (cached adapter only)
E Adapter buffer test phase 2 (cached adapter only)
F Adapter buffer test phase 3 (cached adapter only)
G Adapter buffer test phase 4 (cached adapter only)
H Adapter information test state
I Device assignment sequence
J Device not ready
K Device reset
L Device starting phase
M Device in process of starting
N Device block size determination
O Device self-test
P Device single (LBA) read
Q Device double (LBA) read
S Error occurred after device testing had completed

ROM ERRORS -- Replace System Board except for

C0000-ROM Error -- Replace Keyboard/Timer card (3270 PC models)
CA000-ROM Error -- Replace Keyboard/Timer card (3270 PC models)
C8000-ROM Error -- Replace Fixed Disk Adapter
D0000-ROM Error -- Replace Cluster Adapter
D8000-ROM Error -- Replace Store Loop Adapter

PCjr POST Error codes:

ERROR A....usually caused by a memory (RAM) diagnostic error
ERROR B....usually caused by a KEYBOARD/KYBD adapter diagnostic error
ERROR C....usually caused by a CASSETTE/CASS. adapter diagnostic error
ERROR D....usually caused by a SERIAL/SER. port adapter diag. error
ERROR E....usually caused by the internal MODEM diagnostic error
ERROR F/G..usually caused by a CRC error from the ROM cartridge(s)
ERROR H....usually caused by the DISKETTE/DISK. adapter diag. error

FATAL INTERNAL STACK ERROR -- DOS Problem (also reported as keyboard problem)
As documented in DOS 3.2's Appendix B, just add a command to your CONFIG.SYS file: 'STACKS=3D18,256'. Default for stacks is 9,128. Doubling helps when t= here are many hardware interrupts. ------------------------------------------------------------------------- <= br> An error code via a blinking hard-disk light... can occasionally be interpr= eted -- for example: On one brand of drive one short blink followed by three long blinks is in fact an error indication generated by the drive electronics. It indicates that the drive is "Not Ready" after failing to "calibrate track zero" It usually means that the drive is dead or dying.