HOW-TO - Ethernet Cables<= o:p>

&nb= sp;

Okay, he= re is the basic information you will need to make your own Ethernet cables. =

Parts:<= /h3>
You'll n= eed several feet of CAT 5/5e/6 cable, RJ45 ends and an RJ45 crimper to complete this. You'll also need a nice cut-off pliers. A = wire stripper and a cable tester are greatly helpful as well. =

Cable:<= /h3>
First, s= tart off with good quality cable, it has to be UTP (Unshielded Twisted Pair) Category 5/5e/6 cable, don't skimp on this (Shielded works too, but isn't necessary). Bulk cable comes in many types, there are 2 basic categories, solid and braided cable. Braided cable tends to work better in "patch" applications for desktop use. It is more flexible and res= ilient than solid cable and easier to work with, but really meant for shorter leng= ths. Solid cable is meant for longer runs in a fixed position. Plenum rated cable should/must be used whenever the cable travels through an air circulation space. For example, above a false ceiling or below a ra= ised floor.
Your likely going to want braided type cable.

Here is what the internals= of the cable look like:

Figure 1 - Internal Cable Structure and Color Coding

There are 8 color coded wi= res. These wires are twisted into 4 pairs of wires, e= ach pair has a common color theme. One wire in the pair being a solid or primar= ily solid colored wire and the other being a primarily white wire with a colored stripe (Sometimes cheap cable doesn’t have any color on the striped cable, the only way to tell is to check which other wire it is twisted arou= nd). Examples of the naming schemes used are: Orange (alternatively Orange/White) for t= he solid colored wire and White/Orange for the striped cable. The twists are extremely important. They are there to counteract noise and interference. I= t is important to wire according to a standard to get proper performance from the cable. The hardware expects the cable to have certain p= roperties, a cable that does not fall within tolerance will cause errors and or failur= es. Besides, this maintains all your cables to the standards and makes it easy = to find errors and cross-over cables. The standard I'm referring to, is primarily the TIA/EIA-568-A standard. This stan= dard specifies two wiring standards for a 8-position modular connector such as is used in twisted pair Ethernet networks. The two wiring standards, T568A and T568B vary only in the arrangement of the color= ed pairs. As shown below I have chosen T568B for the straight through cable and T568A for the cross-over cable. I believe this to be the most common arrangement for Ethernet cables. It is also possible to wire it the opposite way (i.e. straight through is a T568A). Your choice might be determined by = the need to match existing wiring, jacks or personal preference, but you should maintain consistency.

RJ45 Ends:

The RJ45= end is a 8-position modular connector that looks like a large= phone plug. There are a couple variations available. The primary variation you ne= ed to pay attention to is whether the connector is intended for braided or sol= id wire. For braided/stranded wires, the connector has contacts that actually pierce the wire. For solid wires, the connector has fingers which pierce the insulation and make contact with the wire by grasping it from both sides. T= he connector is the weak point in an Ethernet cable, choosing the wrong one wi= ll often cause grief later. If you just walk into a computer store, it's pretty impossible to tell what type of connector it is, if it isn't specifically l= abeled. Strain relief boots are somewhat helpful sometimes. Here is a diagram and p= in out:

3D"rj45 3D"rj45
Figure 2 - RJ45 Jack and Plug Pin out

Ethernet Cables:

Now, on to the cables. There are two basic cables. A straight through cable, which is used to conn= ect to a hub or switch, and a cross-over cable used to operate in a peer-to-peer fashion without a hub/switch. Some interfaces can cross and un-cross a cable automatically as needed, really quite nice. Since you are making your own cables, I will assume you understand which cable you need.

Standard, Straight-Through Wiring (both ends are the same):

RJ45 Pin #	Wire Color	Wire Diagram	10B= ase-T/100Base-TX Signal	100= 0Base-T Signal
1	White/Orange		Transmit+	BI_DA+</CENTER< td>=
2	Orange		Transmit-	BI_DA-</CENTER< td>=
3	White/Green		Receive+	BI_DB+</CENTER< td>=
4	Blue		Unused	BI_DC+</CENTER< td>=
5	White/Blue		Unused	BI_DC-</CENTER< td>=
6	Green		Receive-	BI_DB-</CENTER< td>=
7	White/Brown		Unused	BI_DD+</CENTER< td>=
8	Brown		Unused	BI_DD-</CENTER< td>=

Table= 1 - Straight-Through Cable Pin out

Cross-Over Cable:

<= b>RJ45 Pin # (END 1)	<= b>Wire Color	<= b>Diagram End #1
<= span style=3D'font-family:Arial;color:black'>1	<= span style=3D'font-family:Arial;color:black'>White/Orange	<= span style=3D'font-family:Arial;color:black'>
<= span style=3D'font-family:Arial;color:black'>2	<= st1:City>Orange	<= span style=3D'font-family:Arial;color:black'>
<= span style=3D'font-family:Arial;color:black'>3	<= span style=3D'font-family:Arial;color:black'>White/Green	<= span style=3D'font-family:Arial;color:black'>
<= span style=3D'font-family:Arial;color:black'>4	<= span style=3D'font-family:Arial;color:black'>Blue	<= span style=3D'font-family:Arial;color:black'>
<= span style=3D'font-family:Arial;color:black'>5	<= span style=3D'font-family:Arial;color:black'>White/Blue	<= span style=3D'font-family:Arial;color:black'>
<= span style=3D'font-family:Arial;color:black'>6	<= span style=3D'font-family:Arial;color:black'>Green	<= span style=3D'font-family:Arial;color:black'>
<= span style=3D'font-family:Arial;color:black'>7	<= span style=3D'font-family:Arial;color:black'>White/Brown	<= span style=3D'font-family:Arial;color:black'>
<= span style=3D'font-family:Arial;color:black'>8	<= span style=3D'font-family:Arial;color:black'>Brown	<= span style=3D'font-family:Arial;color:black'>

RJ45 Pin # (END 2)	Wire Color	Diagram End #2
1	White/Green
2	Green
3	White/Orange
4	White/Brown
5	Brown
6	Orange
7	Blue
8	White/Blue

Tables 2 & 3 - Cross-Over Cable Pin outs

+Note: The crossover cable layout has been updated for 1000Base-T operation.

Procedure:

To creat= e the cable, strip off about 2 inches of the cable sheath. When you get to the se= cond side, cut the wire to length and make sure it is more than long enough for = your needs. Remember, an end to end connection should extend at least 1m (3ft) a= nd not more than 100m (~328ft). Yes, there is a minimum, i= ts little known, little referred to and not usually important, but I have seen cases where short cables caused problems. The longer the cable becomes the = more it may affect performance, usually it is a gradual decrease in speed and increase in latency. When uplinking between (cascading) hubs/switches, you usually need a very short cable, less than 1m, check the device's specifications.

Next untwist the pairs, do= n't untwist them beyond what you have exposed, the more untwisted cable you have the worse the problems you can run into.

Now you want to align the colored wires according to the diagrams above. When nicely aligned, hold th= em in line together and trim them all to the same length, about 1/2" to 3/4" left exposed from the sheath. And then you want to insert them in= to the RJ45 end and make sure each wire is fully inserted to the front of the = RJ45 end and in the correct order. The sheath of the cable should extend into the RJ45 end by about 1/2" and will be held in place by the crimp. Crimp t= he end with the crimper tool and once again verify the wires ended up the right order and that the wires extend to the front of the RJ45 end and make good contact with the metal contacts in the RJ45 end. If you have a cable tester, put it to use, and verify the proper connectivity of your newly made cable.=

That should be it, if your= cable doesn't turn out, look closely at each end and see if you can find the prob= lem. Usually a wire ended up in the wrong place or more commonly, one of the wir= es didn't extend to the front of the RJ45 connector and is making no, or poor contact. If you see a mistake or problem, cut the end off and start again. =